When SPI is used for control, the driver must hold the SPI bus lock
while issuing the sequence of writes to perform a soft reset.
>From the time the driver writes the SYSTEM_RESET command until the
driver does a write to terminate the reset, there must not be any
activity on the SPI bus lines. If there is any SPI activity during the
soft-reset, another soft-reset will be triggered. The state of the SPI
chip select is irrelevant.
A repeated soft-reset does not in itself cause any problems, and it is
not an infinite loop. The problem is a race between these resets and
the driver polling for boot completion. There is a time window between
soft resets where the driver could read HALO_STATE as 2 (fully booted)
while the chip is actually soft-resetting. Although this window is
small, it is long enough that it is possible to hit it in normal
operation.
To prevent this race and ensure the chip really is fully booted, the
driver calls spi_bus_lock() to prevent other activity while resetting.
It then issues the SYSTEM_RESET mailbox command. After allowing
sufficient time for reset to take effect, the driver issues a PING
mailbox command, which will force completion of the full soft-reset
sequence. The SPI bus lock can then be released. The mailbox is
checked for any boot or wakeup response from the firmware, before the
value in HALO_STATE will be trusted.
This does not affect SoundWire or I2C control.
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ES8328 codec driver, which is also used for the ES8388 chip that
appears to have an identical register map, claims that the output can
either take the route from DAC->Mixer->Output or through DAC->Output
directly. To the best of what I could find, this is not true, and
creates problems.
Without DACCONTROL17 bit index 7 set for the left channel, as well as
DACCONTROL20 bit index 7 set for the right channel, I cannot get any
analog audio out on Left Out 2 and Right Out 2 respectively, despite the
DAPM routes claiming that this should be possible. Furthermore, the same
is the case for Left Out 1 and Right Out 1, showing that those two don't
have a direct route from DAC to output bypassing the mixer either.
Those control bits toggle whether the DACs are fed (stale bread?) into
their respective mixers. If one "unmutes" the mixer controls in
alsamixer, then sure, the audio output works, but if it doesn't work
without the mixer being fed the DAC input then evidently it's not a
direct output from the DAC.
ES8328/ES8388 are seemingly not alone in this. ES8323, which uses a
separate driver for what appears to be a very similar register map,
simply flips those two bits on in its probe function, and then pretends
there is no power management whatsoever for the individual controls.
Fair enough.
My theory as to why nobody has noticed this up to this point is that
everyone just assumes it's their fault when they had to unmute an
additional control in ALSA.
Fix this in the es8328 driver by removing the erroneous direct route,
then get rid of the playback switch controls and have those bits tied to
the mixer's widget instead, which until now had no register to play
with.
Fixes: 567e4f9892 ("ASoC: add es8328 codec driver")
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://patch.msgid.link/20250222-es8328-route-bludgeoning-v1-1-99bfb7fb22d9@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For systems which load firmware on the cs35l41 which use ACPI, the
_SUB value is used to differentiate firmware and tuning files for the
individual systems. In the case where a system does not have a _SUB
defined in ACPI node for cs35l41, there needs to be a fallback to
allow the files for that system to be differentiated. Since all
ACPI nodes for cs35l41 should have a HID defined, the HID should be a
safe option.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Tested-by: André Almeida <andrealmeid@igalia.com>
Link: https://patch.msgid.link/20250205164806.414020-1-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound fixes from Takashi Iwai:
"Here is a collection of fixes that have been gathered since the
previous pull request.
All about device-specific fixes and quirks, and most of them are
pretty small and trivial"
* tag 'sound-fix-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: hda/realtek: Workaround for resume on Dell Venue 11 Pro 7130
ALSA: hda: Fix headset detection failure due to unstable sort
ALSA: pcm: use new array-copying-wrapper
ASoC: codec: es8316: "DAC Soft Ramp Rate" is just a 2 bit control
ASoC: amd: acp: Fix possible deadlock
firmware: cs_dsp: FW_CS_DSP_KUNIT_TEST should not select REGMAP
ALSA: usb-audio: Add delay quirk for iBasso DC07 Pro
ALSA: hda/realtek: Fix quirk matching for Legion Pro 7
ASoC: renesas: SND_SIU_MIGOR should depend on DMADEVICES
ASoC: Intel: bytcr_rt5640: Add DMI quirk for Vexia Edu Atla 10 tablet 5V
ASoC: da7213: Initialize the mutex
ASoC: use to_platform_device() instead of container_of()
ASoC: acp: Support microphone from Lenovo Go S
ASoC: SOF: imx8m: Add entry for new 8M Plus revision
ASoC: SOF: imx8: Add entries for new 8QM and 8QXP revisions
ASoC: SOF: imx: Add mach entry to select cs42888 topology
dt-bindings: arm: imx: Add board revisions for i.MX8MP, i.MX8QM and i.MX8QXP
ASoC: fsl_asrc_m2m: select CONFIG_DMA_SHARED_BUFFER
ASoC: audio-graph-card2: use correct endpoint when getting link parameters
ASoC: SOF: imx8m: add SAI2,5,6,7
...
ASoC: Fixes for v6.14
A bunch of fixes that came in during the merge window, plus a few new
device IDs. The i.MX changes are a little large since they add some new
quirk data as well as device IDs, and the audio graph card change for
picking the correct endpoint for links is large due to updating a number
of call sites.
Pull sound updates from Takashi Iwai:
"This was a relatively calm cycle, and most of changes are rather small
device-specific fixes. Here are highlights:
Core:
- Further enhancements of ALSA rawmidi and sequencer APIs for MIDI
2.0
- compress-offload API extensions for ASRC support
ASoC:
- Allow clocking on each DAI in an audio graph card to be configured
separately
- Improved power management for Renesas RZ-SSI
- KUnit testing for the Cirrus DSP framework
- Memory to meory operation support for Freescale/NXP platforms
- Support for pause operations in SOF
- Support for Allwinner suinv F1C100s, Awinc AW88083, Realtek
ALC5682I-VE
HD- and USB-audio:
- Add support for Focusrite Scarlett 4th Gen 16i16, 18i16, and 18i20
interfaces via new FCP driver
- TAS2781 SPI HD-audio sub-codec support
- Various device-specific quirks as usual"
* tag 'sound-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (235 commits)
ALSA: hda: tas2781-spi: Fix bogus error handling in tas2781_hda_spi_probe()
ALSA: hda: tas2781-spi: Fix error code in tas2781_read_acpi()
ALSA: hda: tas2781-spi: Delete some dead code
ALSA: usb: fcp: Fix return code from poll ops
ALSA: usb: fcp: Fix incorrect resp->opcode retrieval
ALSA: usb: fcp: Fix meter_levels type to __le32
ALSA: hda/realtek: Enable Mute LED on HP Laptop 14s-fq1xxx
ALSA: hda: tas2781-spi: Fix -Wsometimes-uninitialized in tasdevice_spi_switch_book()
ALSA: ctxfi: Simplify dao_clear_{left,right}_input() functions
ALSA: hda: tas2781-spi: select CRC32 instead of CRC32_SARWATE
ALSA: usb: fcp: Fix hwdep read ops types
ALSA: scarlett2: Add device_setup option to use FCP driver
ALSA: FCP: Add Focusrite Control Protocol driver
ALSA: hda/tas2781: Add tas2781 hda SPI driver
ALSA: hda/realtek - Fixed headphone distorted sound on Acer Aspire A115-31 laptop
ASoC: xilinx: xlnx_spdif: Simpify using devm_clk_get_enabled()
ALSA: hda: Support for Ideapad hotkey mute LEDs
ASoC: Intel: sof_sdw: Fix DMI match for Lenovo 83JX, 83MC and 83NM
ASoC: Intel: sof_sdw: Fix DMI match for Lenovo 83LC
ASoC: dapm: add support for preparing streams
...
Pull drm updates from Dave Airlie:
"There are two external interactions of note, the msm tree pull in some
opp tree, hopefully the opp tree arrives from the same git tree
however it normally does.
There is also a new cgroup controller for device memory, that is used
by drm, so is merging through my tree. This will hopefully help open
up gpu cgroup usage a bit more and move us forward.
There is a new accelerator driver for the AMD XDNA Ryzen AI NPUs.
Then the usual xe/amdgpu/i915/msm leaders and lots of changes and
refactors across the board:
core:
- device memory cgroup controller added
- Remove driver date from drm_driver
- Add drm_printer based hex dumper
- drm memory stats docs update
- scheduler documentation improvements
new driver:
- amdxdna - Ryzen AI NPU support
connector:
- add a mutex to protect ELD
- make connector setup two-step
panels:
- Introduce backlight quirks infrastructure
- New panels: KDB KD116N2130B12, Tianma TM070JDHG34-00,
- Multi-Inno Technology MI1010Z1T-1CP11
bridge:
- ti-sn65dsi83: Add ti,lvds-vod-swing optional properties
- Provide default implementation of atomic_check for HDMI bridges
- it605: HDCP improvements, MCCS Support
xe:
- make OA buffer size configurable
- GuC capture fixes
- add ufence and g2h flushes
- restore system memory GGTT mappings
- ioctl fixes
- SRIOV PF scheduling priority
- allow fault injection
- lots of improvements/refactors
- Enable GuC's WA_DUAL_QUEUE for newer platforms
- IRQ related fixes and improvements
i915:
- More accurate engine busyness metrics with GuC submission
- Ensure partial BO segment offset never exceeds allowed max
- Flush GuC CT receive tasklet during reset preparation
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs
- Fix DG1 power gate sequence
- Enabling uncompressed 128b/132b UHBR SST
- Handle hdmi connector init failures, and no HDMI/DP cases
- More robust engine resets on Haswell and older
i915/xe display:
- HDCP fixes for Xe3Lpd
- New GSC FW ARL-H/ARL-U
- support 3 VDSC engines 12 slices
- MBUS joining sanitisation
- reconcile i915/xe display power mgmt
- Xe3Lpd fixes
- UHBR rates for Thunderbolt
amdgpu:
- DRM panic support
- track BO memory stats at runtime
- Fix max surface handling in DC
- Cleaner shader support for gfx10.3 dGPUs
- fix drm buddy trim handling
- SDMA engine reset updates
- Fix doorbell ttm cleanup
- RAS updates
- ISP updates
- SDMA queue reset support
- Rework DPM powergating interfaces
- Documentation updates and cleanups
- DCN 3.5 updates
- Use a pm notifier to more gracefully handle VRAM eviction on
suspend or hibernate
- Add debugfs interfaces for forcing scheduling to specific engine
instances
- GG 9.5 updates
- IH 4.4 updates
- Make missing optional firmware less noisy
- PSP 13.x updates
- SMU 13.x updates
- VCN 5.x updates
- JPEG 5.x updates
- GC 12.x updates
- DC FAMS updates
amdkfd:
- GG 9.5 updates
- Logging improvements
- Shader debugger fixes
- Trap handler cleanup
- Cleanup includes
- Eviction fence wq fix
msm:
- MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
- DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two
SSPPs for a single plane)
- added CWB hardware blocks support
- DSI:
- added SM6150 (aka QCS615) support
- GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
rcar-du:
- Add r8a779h0 Support
ivpu:
- Fix qemu crash when using passthrough
nouveau:
- expose GSP-RM logging buffers via debugfs
panfrost:
- Add MT8188 Mali-G57 MC3 support
rockchip:
- Gamma LUT support
hisilicon:
- new HIBMC support
virtio-gpu:
- convert to helpers
- add prime support for scanout buffers
v3d:
- Add DRM_IOCTL_V3D_PERFMON_SET_GLOBAL
vc4:
- Add support for BCM2712
vkms:
- line-per-line compositing algorithm to improve performance
zynqmp:
- Add DP audio support
mediatek:
- dp: Add sdp path reset
- dp: Support flexible length of DP calibration data
etnaviv:
- add fdinfo memory support
- add explicit reset handling"
* tag 'drm-next-2025-01-17' of https://gitlab.freedesktop.org/drm/kernel: (1070 commits)
drm/bridge: fix documentation for the hdmi_audio_prepare() callback
doc/cgroup: Fix title underline length
drm/doc: Include new drm-compute documentation
cgroup/dmem: Fix parameters documentation
cgroup/dmem: Select PAGE_COUNTER
kernel/cgroup: Remove the unused variable climit
drm/display: hdmi: Do not read EDID on disconnected connectors
drm/tests: hdmi: Add connector disablement test
drm/connector: hdmi: Do atomic check when necessary
drm/amd/display: 3.2.316
drm/amd/display: avoid reset DTBCLK at clock init
drm/amd/display: improve dpia pre-train
drm/amd/display: Apply DML21 Patches
drm/amd/display: Use HW lock mgr for PSR1
drm/amd/display: Revised for Replay Pseudo vblank control
drm/amd/display: Add a new flag for replay low hz
drm/amd/display: Remove unused read_ono_state function from Hwss module
drm/amd/display: Do not elevate mem_type change to full update
drm/amd/display: Do not wait for PSR disable on vbl enable
drm/amd/display: Remove unnecessary eDP power down
...
ASoC: Updates for v6.14
This was quite a quiet release for what I imagine are holiday related
reasons, the diffstat is dominated by some Cirrus Logic Kunit tests.
There's the usual mix of small improvements and fixes, plus a few new
drivers and features. The diffstat includes some DRM changes due to
work on HDMI audio.
- Allow clocking on each DAI in an audio graph card to be configured
separately.
- Improved power management for Renesas RZ-SSI.
- KUnit testing for the Cirrus DSP framework.
- Memory to meory operation support for Freescale/NXP platforms.
- Support for pause operations in SOF.
- Support for Allwinner suinv F1C100s, Awinc AW88083, Realtek
ALC5682I-VE
There is no audio output if Speaker volume is set above 25.
According to datasheet Rev 2.5 maximum allowed value for the
Speaker output is 0b11001 (25)
0x6D CLASSD_GAIN_1/ 0x6E CLASSD_GAIN_2:
Left/Right Channel Class-D Driver Gain For DAC Left/Right
Input
(Step size is 1dB.)
00000 = Mute (DEFAULT)
00001 = 0dB
00002 = 1dB
...
11000 = 23dB
11001 = 24dB
So adjust this value in accordance with the datasheet.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://patch.msgid.link/20241219042227.7075-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from wangweidong.a@awinic.com:
Add the awinic,aw88083 property to support the aw88083 chip.
The driver is for amplifiers aw88083 of Awinic Technology
Corporation. The AW88083 is an intelligent digital audio
amplifier with low noise.
One specific test condition: the default registers of p[j].reg ~
p[j+3].reg are 0, TASDEVICE_REG(0x00, 0x14, 0x38)(PLT_FLAG_REG),
TASDEVICE_REG(0x00, 0x14, 0x40)(SINEGAIN_REG), and
TASDEVICE_REG(0x00, 0x14, 0x44)(SINEGAIN2_REG). After first calibration,
they are freshed to TASDEVICE_REG(0x00, 0x1a, 0x20), TASDEVICE_REG(0x00,
0x16, 0x58)(PLT_FLAG_REG), TASDEVICE_REG(0x00, 0x14, 0x44)(SINEGAIN_REG),
and TASDEVICE_REG(0x00, 0x16, 0x64)(SINEGAIN2_REG) via "Calibration Start"
kcontrol. In second calibration, the p[j].reg ~ p[j+3].reg have already
become tas2781_cali_start_reg. However, p[j+2].reg, TASDEVICE_REG(0x00,
0x14, 0x44)(SINEGAIN_REG), will be freshed to TASDEVICE_REG(0x00, 0x16,
0x64), which is the third register in the input params of the kcontrol.
This is why only first calibration can work, the second-time, third-time
or more-time calibration always failed without reboot. Of course, if no
p[j].reg is in the list of tas2781_cali_start_reg, this stress test can
work well.
Fixes: 49e2e353fb ("ASoC: tas2781: Add Calibration Kcontrols for Chromebook")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20241211043859.1328-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-21-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-20-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-19-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-18-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-17-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-16-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-15-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20241203200001.197295-14-afd@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
