IEP driver supports both perout and pps signal generation
but perout feature is faulty with half-cooked support
due to some missing configuration. Remove perout
support from the driver and reject perout requests with
"not supported" error code.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250227092441.1848419-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For successful XDP_TX and XDP_REDIRECT cases, the packet was received
successfully so update RX statistics. Use original received
packet length for that.
TX packets statistics are incremented on TX completion so don't
update it while TX queueing.
If xdp_convert_buff_to_frame() fails, increment tx_dropped.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Fixes: 8acacc40f7 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Link: https://patch.msgid.link/20250210-am65-cpsw-xdp-fixes-v1-2-ec6b1f7f1aca@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the XDP program doesn't result in XDP_PASS then we leak the
memory allocated by am65_cpsw_build_skb().
It is pointless to allocate SKB memory before running the XDP
program as we would be wasting CPU cycles for cases other than XDP_PASS.
Move the SKB allocation after evaluating the XDP program result.
This fixes the memleak. A performance boost is seen for XDP_DROP test.
XDP_DROP test:
Before: 460256 rx/s 0 err/s
After: 784130 rx/s 0 err/s
Fixes: 8acacc40f7 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250210-am65-cpsw-xdp-fixes-v1-1-ec6b1f7f1aca@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are missing netif_napi_del() and am65_cpsw_nuss_free_tx/rx_chns()
in error path when am65_cpsw_nuss_init_tx/rx_chns() is used anywhere
other than at probe(). i.e. am65_cpsw_nuss_update_tx_rx_chns and
am65_cpsw_nuss_resume()
As reported, in am65_cpsw_nuss_update_tx_rx_chns(),
if am65_cpsw_nuss_init_tx_chns() partially fails then
devm_add_action(dev, am65_cpsw_nuss_free_tx_chns,..) is added
but the cleanup via am65_cpsw_nuss_free_tx_chns() will not run.
Same issue exists for am65_cpsw_nuss_init_tx/rx_chns() failures
in am65_cpsw_nuss_resume() as well.
This would otherwise require more instances of devm_add/remove_action
and is clearly more of a distraction than any benefit.
So, drop devm_add/remove_action for am65_cpsw_nuss_free_tx/rx_chns()
and call am65_cpsw_nuss_free_tx/rx_chns() and netif_napi_del()
where required.
Reported-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Closes: https://lore.kernel.org/all/m4rhkzcr7dlylxr54udyt6lal5s2q4krrvmyay6gzgzhcu4q2c@r34snfumzqxy/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250117-am65-cpsw-streamline-v2-1-91a29c97e569@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When getting the IRQ we use k3_udma_glue_tx_get_irq() which returns
negative error value on error. So not NULL check is not sufficient
to deteremine if IRQ is valid. Check that IRQ is greater then zero
to ensure it is valid.
There is no issue at probe time but at runtime user can invoke
.set_channels which results in the following call chain.
am65_cpsw_set_channels()
am65_cpsw_nuss_update_tx_rx_chns()
am65_cpsw_nuss_remove_tx_chns()
am65_cpsw_nuss_init_tx_chns()
At this point if am65_cpsw_nuss_init_tx_chns() fails due to
k3_udma_glue_tx_get_irq() then tx_chn->irq will be set to a
negative value.
Then, at subsequent .set_channels with higher channel count we
will attempt to free an invalid IRQ in am65_cpsw_nuss_remove_tx_chns()
leading to a kernel warning.
The issue is present in the original commit that introduced this driver,
although there, am65_cpsw_nuss_update_tx_rx_chns() existed as
am65_cpsw_nuss_update_tx_chns().
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add multicast filtering support for VLAN interfaces in HSR offload mode
for ICSSG driver.
The driver calls vlan_for_each() API on the hsr device's ndev to get the
list of available vlans for the hsr device. The driver then sync mc addr of
vlan interface with a locally mainatined list emac->vlan_mcast_list[vid]
using __hw_addr_sync_multiple() API.
The driver then calls the sync / unsync callbacks.
In the sync / unsync call back, driver checks if the vdev's real dev is
hsr device or not. If the real dev is hsr device, driver gets the per
port device using hsr_get_port_ndev() and then driver passes appropriate
vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add multicast filtering support for VLAN interfaces in dual EMAC mode
for ICSSG driver.
The driver uses vlan_for_each() API to get the list of available
vlans. The driver then sync mc addr of vlan interface with a locally
mainatined list emac->vlan_mcast_list[vid] using __hw_addr_sync_multiple()
API.
__hw_addr_sync_multiple() is used instead of __hw_addr_sync() to sync
vdev->mc with local list because the sync_cnt for addresses in vdev->mc
will already be set by the vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c]
and __hw_addr_sync() only syncs when the sync_cnt == 0. Whereas
__hw_addr_sync_multiple() can sync addresses even if sync_cnt is not 0.
Export __hw_addr_sync_multiple() so that driver can use it.
Once the local list is synced, driver calls __hw_addr_sync_dev() with
the local list, vdev, sync and unsync callbacks.
__hw_addr_sync_dev() is used with the local maintained list as the list
to synchronize instead of using __dev_mc_sync() on vdev because
__dev_mc_sync() on vdev will call __hw_addr_sync_dev() on vdev->mc and
sync_cnt for addresses in vdev->mc will already be set by the
vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c] and __hw_addr_sync_dev()
only syncs if the sync_cnt of addresses in the list (vdev->mc in this case)
is 0. Whereas __hw_addr_sync_dev() on local list will work fine as the
sync_cnt for addresses in the local list will still be 0.
Based on change in addresses in the local list, sync / unsync callbacks
are invoked. In the sync / unsync API in driver, based on whether the ndev
is vlan or not, driver passes appropriate vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CPSW ALE has 75-bit ALE entries stored across three 32-bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions support
ALE field entries spanning up to two words at the most.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions work as
expected when ALE field spanned across word1 and word2, but fails when
ALE field spanned across word2 and word3.
For example, while reading the ALE field spanned across word2 and word3
(i.e. bits 62 to 64), the word3 data shifted to an incorrect position
due to the index becoming zero while flipping.
The same issue occurred when setting an ALE entry.
This issue has not been seen in practice but will be an issue in the future
if the driver supports accessing ALE fields spanning word2 and word3
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: b685f1a589 ("net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()")
Signed-off-by: Sudheer Kumar Doredla <s-doredla@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250108172433.311694-1-s-doredla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When ICSSG interfaces are brought down and brought up again, the
pru cores are shut down and booted again, flushing out all the memories
and start again in a clean state. Hence it is expected that the
IEP_CMP_CFG register needs to be flushed during iep_init() to ensure
that the existing residual configuration doesn't cause any unusual
behavior. If the register is not cleared, existing IEP_CMP_CFG set for
CMP1 will result in SYNC0_OUT signal based on the SYNC_OUT register values.
After bringing the interface up, calling PPS enable doesn't work as
the driver believes PPS is already enabled, (iep->pps_enabled is not
cleared during interface bring down) and driver will just return true
even though there is no signal. Fix this by disabling pps and perout.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0
and SLICE1. Currently whenever any ICSSG interface comes up we load the
respective firmwares to PRU cores and whenever interface goes down, we
stop the resective cores. Due to this, when SLICE0 goes down while
SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is
stopped. This results in clock jump for SLICE1 interface as the timesync
related operations are no longer running.
As there are interdependencies between SLICE0 and SLICE1 firmwares,
fix this by running both PRU0 and PRU1 firmwares as long as at least 1
ICSSG interface is up. Add new flag in prueth struct to check if all
firmwares are running and remove the old flag (fw_running).
Use emacs_initialized as reference count to load the firmwares for the
first and last interface up/down. Moving init_emac_mode and fw_offload_mode
API outside of icssg_config to icssg_common_start API as they need
to be called only once per firmware boot.
Change prueth_emac_restart() to return error code and add error prints
inside the caller of this functions in case of any failures.
Move prueth_emac_stop() from common to sr1 driver.
sr1 and sr2 drivers have different logic handling for stopping
the firmwares. While sr1 driver is dependent on emac structure
to stop the corresponding pru cores for that slice, for sr2
all the pru cores of both the slices are stopped and is not
dependent on emac. So the prueth_emac_stop() function is no
longer common and can be moved to sr1 driver.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Host Port (i.e. CPU facing port) of CPSW receives traffic from Linux
via TX DMA Channels which are Hardware Queues consisting of traffic
categorized according to their priority. The Host Port is configured to
dequeue traffic from these Hardware Queues on the basis of priority i.e.
as long as traffic exists on a Hardware Queue of a higher priority, the
traffic on Hardware Queues of lower priority isn't dequeued. An alternate
operation is also supported wherein traffic can be dequeued by the Host
Port in a Round-Robin manner.
Until commit under Fixes, the am65-cpsw driver enabled a single TX DMA
Channel, due to which, unless modified by user via "ethtool", all traffic
from Linux is transmitted on DMA Channel 0. Therefore, configuring
the Host Port for priority based dequeuing or Round-Robin operation
is identical since there is a single DMA Channel.
Since commit under Fixes, all 8 TX DMA Channels are enabled by default.
Additionally, the default "tc mapping" doesn't take into account
the possibility of different traffic profiles which various users
might have. This results in traffic starvation at the Host Port
due to the priority based dequeuing which has been enabled by default
since the inception of the driver. The traffic starvation triggers
NETDEV WATCHDOG timeout for all TX DMA Channels that haven't been serviced
due to the presence of traffic on the higher priority TX DMA Channels.
Fix this by defaulting to Round-Robin dequeuing at the Host Port, which
shall ensure that traffic is dequeued from all TX DMA Channels irrespective
of the traffic profile. This will address the NETDEV WATCHDOG timeouts.
At the same time, users can still switch from Round-Robin to Priority
based dequeuing at the Host Port with the help of the "p0-rx-ptype-rrobin"
private flag of "ethtool". Users are expected to setup an appropriate
"tc mapping" that suits their traffic profile when switching to priority
based dequeuing at the Host Port.
Fixes: be397ea347 ("net: ethernet: am65-cpsw: Set default TX channels to maximum")
Cc: <stable@vger.kernel.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20241220075618.228202-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems the cpsw MAC doesn't support EEE. See e.g. the commit message of
ce2899428e ("ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY").
There are cases where this causes issues if the PHY's on both sides have
negotiated EEE. As a workaround EEE modes of the PHY are marked broken
in DT, effectively disabling EEE advertisement.
Improve this by using new function phy_disable_eee() in the MAC driver.
This properly disables EEE advertisement, and allows to remove the
eee-broken-xxx properties from DT. As EEE is disabled anyway, we can
remove also the set_eee ethtool op.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/d08a798e-8565-422c-b2ed-121794db077f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IEEE802.1Q-2014 supersedes IEEE802.1D-2004. Now Priority Code Point (PCP)
2 is no longer at a lower priority than PCP 0. PCP 1 (Background) is still
at a lower priority than PCP 0 (Best Effort).
Reference:
IEEE802.1Q-2014, Standard for Local and metropolitan area networks
Table I-2 - Traffic type acronyms
Table I-3 - Defining traffic types
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first PPS latch time needs to be calculated by the driver
(in rounded off seconds) and configured as the start time
offset for the cycle. After synchronizing two PTP clocks
running as master/slave, missing this would cause master
and slave to start immediately with some milliseconds
drift which causes the PPS signal to never synchronize with
the PTP master.
Fixes: 186734c158 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20241111095842.478833-1-m-malladi@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
flow->irq is initialized to 0 which is a valid IRQ. Set it to -EINVAL
in error path of am65_cpsw_nuss_init_rx_chns() so we do not try
to free an unallocated IRQ in am65_cpsw_nuss_remove_rx_chns().
If user tried to change number of RX queues and am65_cpsw_nuss_init_rx_chns()
failed due to any reason, the warning will happen if user tries to change
the number of RX queues after the error condition.
root@am62xx-evm:~# ethtool -L eth0 rx 3
[ 40.385293] am65-cpsw-nuss 8000000.ethernet: set new flow-id-base 19
[ 40.393211] am65-cpsw-nuss 8000000.ethernet: Failed to init rx flow2
netlink error: Invalid argument
root@am62xx-evm:~# ethtool -L eth0 rx 2
[ 82.306427] ------------[ cut here ]------------
[ 82.311075] WARNING: CPU: 0 PID: 378 at kernel/irq/devres.c:144 devm_free_irq+0x84/0x90
[ 82.469770] Call trace:
[ 82.472208] devm_free_irq+0x84/0x90
[ 82.475777] am65_cpsw_nuss_remove_rx_chns+0x6c/0xac [ti_am65_cpsw_nuss]
[ 82.482487] am65_cpsw_nuss_update_tx_rx_chns+0x2c/0x9c [ti_am65_cpsw_nuss]
[ 82.489442] am65_cpsw_set_channels+0x30/0x4c [ti_am65_cpsw_nuss]
[ 82.495531] ethnl_set_channels+0x224/0x2dc
[ 82.499713] ethnl_default_set_doit+0xb8/0x1b8
[ 82.504149] genl_family_rcv_msg_doit+0xc0/0x124
[ 82.508757] genl_rcv_msg+0x1f0/0x284
[ 82.512409] netlink_rcv_skb+0x58/0x130
[ 82.516239] genl_rcv+0x38/0x50
[ 82.519374] netlink_unicast+0x1d0/0x2b0
[ 82.523289] netlink_sendmsg+0x180/0x3c4
[ 82.527205] __sys_sendto+0xe4/0x158
[ 82.530779] __arm64_sys_sendto+0x28/0x38
[ 82.534782] invoke_syscall+0x44/0x100
[ 82.538526] el0_svc_common.constprop.0+0xc0/0xe0
[ 82.543221] do_el0_svc+0x1c/0x28
[ 82.546528] el0_svc+0x28/0x98
[ 82.549578] el0t_64_sync_handler+0xc0/0xc4
[ 82.553752] el0t_64_sync+0x190/0x194
[ 82.557407] ---[ end trace 0000000000000000 ]---
Fixes: da70d184a8 ("net: ethernet: ti: am65-cpsw: Introduce multi queue Rx")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On J7 platforms, setting up multiple RX flows was failing
as the RX free descriptor ring 0 is shared among all flows
and we did not allocate enough elements in the RX free descriptor
ring 0 to accommodate for all RX flows.
This issue is not present on AM62 as separate pair of
rings are used for free and completion rings for each flow.
Fix this by allocating enough elements for RX free descriptor
ring 0.
However, we can no longer rely on desc_idx (descriptor based
offsets) to identify the pages in the respective flows as
free descriptor ring includes elements for all flows.
To solve this, introduce a new swdata data structure to store
flow_id and page. This can be used to identify which flow (page_pool)
and page the descriptor belonged to when popped out of the
RX rings.
Fixes: da70d184a8 ("net: ethernet: ti: am65-cpsw: Introduce multi queue Rx")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
W=1 builds flag that some accessor functions for ALE fields are unused.
Address this by splitting up the macros used to define these
accessors to allow only those that are used to be declared.
The warnings are verbose, but for example, the mcast_state case is
flagged by clang-18 as:
.../cpsw_ale.c:220:1: warning: unused function 'cpsw_ale_get_mcast_state' [-Wunused-function]
220 | DEFINE_ALE_FIELD(mcast_state, 62, 2)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../cpsw_ale.c:145:19: note: expanded from macro 'DEFINE_ALE_FIELD'
145 | static inline int cpsw_ale_get_##name(u32 *ale_entry) \
| ^~~~~~~~~~~~~~~~~~~
<scratch space>:196:1: note: expanded from here
196 | cpsw_ale_get_mcast_state
| ^~~~~~~~~~~~~~~~~~~~~~~~
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of struct pcpu_sw_netstats and related helpers to handle
existing per-cpu stats for this driver - the exact same counters
are maintained.
A side effect of this change is to address __percpu warnings
flagged by Sparse:
.../am65-cpsw-nuss.c:2658:55: warning: incorrect type in initializer (different address spaces)
.../am65-cpsw-nuss.c:2658:55: expected struct am65_cpsw_ndev_stats [noderef] __percpu *stats
.../am65-cpsw-nuss.c:2658:55: got void *data
.../am65-cpsw-nuss.c:2781:15: warning: incorrect type in argument 3 (different address spaces)
.../am65-cpsw-nuss.c:2781:15: expected void *data
.../am65-cpsw-nuss.c:2781:15: got struct am65_cpsw_ndev_stats [noderef] __percpu *stats
Compile tested only.
No functional change intended.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/all/20240911170643.7ecb1bbb@kernel.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The id_temp local variable in am65_cpsw_nuss_probe() is
used to hold a 64-bit big-endian value as it is assigned using
cpu_to_be64().
It is read using memcpy(), where it is written as an identifier into a
byte-array. So this can also be treated as big endian.
As it's type is currently host byte order (u64), sparse flags
an endian mismatch when compiling for little-endian systems:
.../am65-cpsw-nuss.c:3454:17: warning: incorrect type in assignment (different base types)
.../am65-cpsw-nuss.c:3454:17: expected unsigned long long [usertype] id_temp
.../am65-cpsw-nuss.c:3454:17: got restricted __be64 [usertype]
Address this by using __be64 as the type of id_temp.
No functional change intended.
Compile tested only.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN table is a shared memory between the two ports/slices
in a ICSSG cluster and this may lead to race condition when the
common code paths for both ports are executed in different CPUs.
Fix the race condition access by locking the shared memory access
Fixes: 487f7323f3 ("net: ti: icssg-prueth: Add helper functions to configure FDB")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of devm_alloc_etherdev_mqs() conflicts with
am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances
get unregistered twice. Switch to alloc_etherdev_mqs() and make sure
am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device
instances properly.
With this, it is finally possible to rmmod the driver without oopsing
the kernel.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <roger@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink()
after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in
devl_port_unregister(). Makes it coherent with usage in
m65_cpsw_nuss_register_ndevs()'s cleanup path.
Fixes: 58356eb31d ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The number of register fields cannot be assumed to be ALE_FIELDS_MAX
as some platforms can have lesser fields.
Solve this by embedding the actual number of fields available
in platform data and use that instead of ALE_FIELDS_MAX.
Gets rid of the below warning on BeagleBone Black
[ 1.007735] WARNING: CPU: 0 PID: 33 at drivers/base/regmap/regmap.c:1208 regmap_field_init+0x88/0x9c
[ 1.007802] invalid empty mask defined
[ 1.007812] Modules linked in:
[ 1.007842] CPU: 0 UID: 0 PID: 33 Comm: kworker/u4:3 Not tainted 6.11.0-01459-g508403ab7b74-dirty #840
[ 1.007867] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 1.007890] Workqueue: events_unbound deferred_probe_work_func
[ 1.007935] Call trace:
[ 1.007957] unwind_backtrace from show_stack+0x10/0x14
[ 1.007999] show_stack from dump_stack_lvl+0x50/0x64
[ 1.008033] dump_stack_lvl from __warn+0x70/0x124
[ 1.008077] __warn from warn_slowpath_fmt+0x194/0x1a8
[ 1.008113] warn_slowpath_fmt from regmap_field_init+0x88/0x9c
[ 1.008154] regmap_field_init from devm_regmap_field_alloc+0x48/0x64
[ 1.008193] devm_regmap_field_alloc from cpsw_ale_create+0xfc/0x320
[ 1.008251] cpsw_ale_create from cpsw_init_common+0x214/0x354
[ 1.008286] cpsw_init_common from cpsw_probe+0x4ac/0xb88
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/CAMuHMdUf-tKRDzkz2_m8qdFTFutefddU0NTratVrEjRTzA3yQQ@mail.gmail.com/
Fixes: 11cbcfeaa7 ("net: ethernet: ti: cpsw_ale: use regfields for number of Entries and Policers")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240924-am65-cpsw-multi-rx-fix-v1-1-0ca3fa9a1398@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The HSR stack allows to offload its Tx packet duplication functionality to
the hardware. Enable this offloading feature for ICSSG driver. Add support
to offload HSR Tx Tag Insertion and Rx Tag Removal and duplicate discard.
hsr tag insertion offload and hsr dup offload are tightly coupled in
firmware implementation. Both these features need to be enabled / disabled
together.
Duplicate discard is done as part of RX tag removal and it is
done by the firmware. When driver sends the r30 command
ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE, firmware does RX tag removal as well as
duplicate discard.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20240911081603.2521729-5-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for offloading HSR port-to-port frame forward to hardware.
When the slave interfaces are added to the HSR interface, the PRU cores
will be stopped and ICSSG HSR firmwares will be loaded to them.
Similarly, when HSR interface is deleted, the PRU cores will be
restarted and the last used firmwares will be reloaded. PRUeth
interfaces will be back to the last used mode.
This commit also renames some APIs that are common between switch and
hsr mode with '_fw_offload' suffix.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20240911081603.2521729-4-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we support multiple RX queues, enable default priority
to flow mapping so that higher priority packets come on higher
channels (flows).
The Classifier checks for PCP/DSCP priority in the packet and
routes them to the appropriate flow.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
