For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).
This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).
Fixes: 976e920183 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127142221.3718184-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added new but not yet supported
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-3-8d3fea6d403d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Amlogic G12A devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b190056fa9 ("arm64: dts: meson-g12a: add cpus OPP table")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20230119053031.21400-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS fixes from Thomas Bogendoerfer:
"Fixes due to DT changes"
* tag 'mips_6.2_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: dts: bcm63268: Add missing properties to the TWD node
MIPS: ralink: mt7621: avoid to init common ralink reset controller
Pull RISC-V kvm updates from Paolo Bonzini:
- Allow unloading KVM module
- Allow KVM user-space to set mvendorid, marchid, and mimpid
- Several fixes and cleanups
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
RISC-V: KVM: Add ONE_REG interface for mvendorid, marchid, and mimpid
RISC-V: KVM: Save mvendorid, marchid, and mimpid when creating VCPU
RISC-V: Export sbi_get_mvendorid() and friends
RISC-V: KVM: Move sbi related struct and functions to kvm_vcpu_sbi.h
RISC-V: KVM: Use switch-case in kvm_riscv_vcpu_set/get_reg()
RISC-V: KVM: Remove redundant includes of asm/csr.h
RISC-V: KVM: Remove redundant includes of asm/kvm_vcpu_timer.h
RISC-V: KVM: Fix reg_val check in kvm_riscv_vcpu_set_reg_config()
RISC-V: KVM: Simplify kvm_arch_prepare_memory_region()
RISC-V: KVM: Exit run-loop immediately if xfer_to_guest fails
RISC-V: KVM: use vma_lookup() instead of find_vma_intersection()
RISC-V: KVM: Add exit logic to main.c
Pull remoteproc updates from Bjorn Andersson:
"rproc-virtio device names are now auto generated, to avoid conflicts
between remoteproc instances.
The imx_rproc driver is extended with support for communicating with
and attaching to a running M4 on i.MX8QXP, as well as support for
attaching to the M4 after self-recovering from a crash. Support is
added for i.MX8QM and mailbox channels are reconnected during the
recovery process, in order to avoid data corruption.
The Xilinx Zynqmp firmware interface is extended and support for the
Xilinx R5 RPU is introduced.
Various resources leaks, primarily in error paths, throughout the
Qualcomm drivers are corrected.
Lastly a fix to ensure that pm_relax is invoked even if the remoteproc
instance is stopped between a crash is being reported and the recovery
handler is scheduled"
* tag 'rproc-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (25 commits)
remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in q6v5_wcss_qcs404_power_on()
remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in adsp_alloc_memory_region()
remoteproc: qcom_q6v5_pas: detach power domains on remove
remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio()
remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
remoteproc: sysmon: Make QMI message rules const
drivers: remoteproc: Add Xilinx r5 remoteproc driver
firmware: xilinx: Add RPU configuration APIs
firmware: xilinx: Add shutdown/wakeup APIs
firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration.
arm64: dts: xilinx: zynqmp: Add RPU subsystem device node
dt-bindings: remoteproc: Add Xilinx RPU subsystem bindings
remoteproc: core: Use device_match_of_node()
remoteproc: imx_rproc: Correct i.MX93 DRAM mapping
remoteproc: imx_rproc: Enable attach recovery for i.MX8QM/QXP
remoteproc: imx_rproc: Request mbox channel later
remoteproc: imx_rproc: Support i.MX8QM
remoteproc: imx_rproc: Support kicking Mcore from Linux for i.MX8QXP
...
The m68 hand-written assembler version of strcmp() has always been
broken: it returns the difference between the first non-matching byte
done as a 8-bit subtraction.
That is _almost_ right, but is broken for the overflow case. The
strcmp() function should indeed return the sign of the difference
between the first byte that differs, but the subtraction needs to be
done in a wider type than 'char'. Otherwise the ordering isn't actually
stable.
This went unnoticed for basically forever, because nobody ever cares
about non-US-ASCII orderings in the kernel (in fact, most users only
care about "exact match or not"), so overflows don't really happen in
practice, even if it was very very wrong.
But that mostly unnoticeable bug becomes very noticeable by the recent
change to make 'char' be unsigned in the kernel across all architectures
(commit 3bc753c06d: "kbuild: treat char as always unsigned"). Because
the code not only did the subtraction in the wrong type width, it also
used 'char' to then make the compiler expand the result from an 8-bit
difference to the 'int' return value.
So now with an unsigned char that incorrect arithmetic width was then
not even sign-expanded, and always returned just a positive integer.
We could re-instate the old broken code by just turning the 'char' into
'signed char' as has been done elsewhere where people depended on the
signedness of 'char', but since the whole function was broken to begin
with, and we have a non-broken default fallback implementation, let's
just remove this broken function entirely.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/lkml/20221221145332.GA2399037@roeck-us.net/
Cc: Jason Donenfeld <Jason@zx2c4.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more random number generator updates from Jason Donenfeld:
"Two remaining changes that are now possible after you merged a few
other trees:
- #include <asm/archrandom.h> can be removed from random.h now,
making the direct use of the arch_random_* API more of a private
implementation detail between the archs and random.c, rather than
something for general consumers.
- Two additional uses of prandom_u32_max() snuck in during the
initial phase of pulls, so these have been converted to
get_random_u32_below(), and now the deprecated prandom_u32_max()
alias -- which was just a wrapper around get_random_u32_below() --
can be removed.
In addition, there is one fix:
- Check efi_rt_services_supported() before attempting to use an EFI
runtime function.
This affected EFI systems that disable runtime services yet still
boot via EFI (e.g. the reporter's Lenovo Thinkpad X13s laptop), as
well systems where EFI runtime services have been forcibly
disabled, such as on PREEMPT_RT.
On those machines, a very early and hard to diagnose crash would
happen, preventing boot"
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove prandom_u32_max()
efi: random: fix NULL-deref when refreshing seed
random: do not include <asm/archrandom.h> from random.h
Commit 38a8553b0a ("clk: ralink: make system controller node a reset provider")
make system controller a reset provider for mt7621 ralink SoCs. Ralink init code
also tries to start previous common reset controller which at the end tries to
find device tree node 'ralink,rt2880-reset'. mt7621 device tree file is not
using at all this node anymore. Hence avoid to init this common reset controller
for mt7621 ralink SoCs to avoid 'Failed to find reset controller node' boot
error trace error.
Fixes: 64b2d6ffff ("staging: mt7621-dts: align resets with binding documentation")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pull m68knommu update from Greg Ungerer:
"Only a single change to use the safer strscpy() instead of strncpy()
when setting up the cmdline"
* tag 'm68knommu-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: use strscpy() to instead of strncpy()
Pull parisc updates from Helge Deller:
"There is one noteable patch, which allows the parisc kernel to use the
same MADV_xxx constants as the other architectures going forward. With
that change only alpha has one entry left (MADV_DONTNEED is 6 vs 4 on
others) which is different. To prevent an ABI breakage, a wrapper is
included which translates old MADV values to the new ones, so existing
userspace isn't affected. Reason for that patch is, that some
applications wrongly used the standard MADV_xxx values even on some
non-x86 platforms and as such those programs failed to run correctly
on parisc (examples are qemu-user, tor browser and boringssl).
Then the kgdb console and the LED code received some fixes, and some
0-day warnings are now gone. Finally, the very last compile warning
which was visible during a kernel build is now fixed too (in the vDSO
code).
The majority of the patches are tagged for stable series and in
summary this patchset is quite small and drops more code than it adds:
Fixes:
- Fix potential null-ptr-deref in start_task()
- Fix kgdb console on serial port
- Add missing FORCE prerequisites in Makefile
- Drop PMD_SHIFT from calculation in pgtable.h
Enhancements:
- Implement a wrapper to align madvise() MADV_* constants with other
architectures
- If machine supports running MPE/XL, show the MPE model string
Cleanups:
- Drop duplicate kgdb console code
- Indenting fixes in setup_cmdline()"
* tag 'parisc-for-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Show MPE/iX model string at bootup
parisc: Add missing FORCE prerequisites in Makefile
parisc: Move pdc_result struct to firmware.c
parisc: Drop locking in pdc console code
parisc: Drop duplicate kgdb_pdc console
parisc: Fix locking in pdc_iodc_print() firmware call
parisc: Drop PMD_SHIFT from calculation in pgtable.h
parisc: Align parisc MADV_XXX constants with all other architectures
parisc: led: Fix potential null-ptr-deref in start_task()
parisc: Fix inconsistent indenting in setup_cmdline()
Convert the final two users of prandom_u32_max() that slipped in during
6.2-rc1 to use get_random_u32_below().
Then, with no more users left, we can finally remove the deprecated
function.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The <asm/archrandom.h> header is a random.c private detail, not
something to be called by other code. As such, don't make it
automatically available by way of random.h.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Pull ARM SoC fixes from Arnd Bergmann:
"These are a couple of build fixes from randconfig testing, plus a set
of Mediatek SoC specific fixes, all trivial"
* tag 'soc-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: tegra: fix CPU_BIG_ENDIAN dependencies
ARM: disallow pre-ARMv5 builds with ld.lld
ARM: pxa: fix building with clang
MAINTAINERS: add related dts to IXP4xx
ARM: dts: spear: drop 0x from unit address
arm64: dts: mt8183: Fix Mali GPU clock
arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon
soc: mediatek: pm-domains: Fix the power glitch issue
Pull Kbuild updates from Masahiro Yamada:
- Support zstd-compressed debug info
- Allow W=1 builds to detect objects shared among multiple modules
- Add srcrpm-pkg target to generate a source RPM package
- Make the -s option detection work for future GNU Make versions
- Add -Werror to KBUILD_CPPFLAGS when CONFIG_WERROR=y
- Allow W=1 builds to detect -Wundef warnings in any preprocessed files
- Raise the minimum supported version of binutils to 2.25
- Use $(intcmp ...) to compare integers if GNU Make >= 4.4 is used
- Use $(file ...) to read a file if GNU Make >= 4.2 is used
- Print error if GNU Make older than 3.82 is used
- Allow modpost to detect section mismatches with Clang LTO
- Include vmlinuz.efi into kernel tarballs for arm64 CONFIG_EFI_ZBOOT=y
* tag 'kbuild-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
buildtar: fix tarballs with EFI_ZBOOT enabled
modpost: Include '.text.*' in TEXT_SECTIONS
padata: Mark padata_work_init() as __ref
kbuild: ensure Make >= 3.82 is used
kbuild: refactor the prerequisites of the modpost rule
kbuild: change module.order to list *.o instead of *.ko
kbuild: use .NOTINTERMEDIATE for future GNU Make versions
kconfig: refactor Makefile to reduce process forks
kbuild: add read-file macro
kbuild: do not sort after reading modules.order
kbuild: add test-{ge,gt,le,lt} macros
Documentation: raise minimum supported version of binutils to 2.25
kbuild: add -Wundef to KBUILD_CPPFLAGS for W=1 builds
kbuild: move -Werror from KBUILD_CFLAGS to KBUILD_CPPFLAGS
kbuild: Port silent mode detection to future gnu make.
init/version.c: remove #include <generated/utsrelease.h>
firmware_loader: remove #include <generated/utsrelease.h>
modpost: Mark uuid_le type to be suitable only for MEI
kbuild: add ability to make source rpm buildable using koji
kbuild: warn objects shared among multiple modules
...
