I relied on the fact that anycast routes use the loopback device as
their nexthop device to trap packets hitting them to the CPU.
After commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") this is no longer the case and such routes are
programmed with a forward action (note the 'offload' flag):
anycast cafe:: dev enp3s0np7 proto kernel metric 0 offload pref medium
This will prevent the router from locally receiving packets destined to
the Subnet-Router anycast address.
Fix this by specifically programming anycast routes with action trap,
which results in the following output:
anycast cafe:: dev enp3s0np7 proto kernel metric 0 pref medium
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan writes:
USB-serial updates for v4.14-rc1
Here are the USB-serial updates for 4.14-rc1; a new option device id and
one device-id clean up.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently loop disables merge. While it makes sense for buffer IO mode,
directio mode can benefit from request merge. Without merge, loop could
send small size IO to underlayer disk and harm performance.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Loop can handle any size of request. Limiting it to 255 sectors just
burns the CPU for bio split and request merge for underlayer disk and
also cause bad fs block allocation in directio mode.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
From Cyrille:
"
This pull request contains the following notable changes:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header
"
Do not check which flash type the SoC was booted from before
using this driver. Assume that the device tree is correct and use this
driver when it was added to device tree. This also removes a build
dependency to the SoC code.
All device trees I am aware of only have one correct flash device entry
in it. The device tree is anyway bundled with the kernel in all systems
using device tree I know of.
The boot mode can be specified with some pin straps and will select the
flash type the rom code will boot from. One SPI, NOR or NAND flash chip
can be connect to the EBU and used to load the first stage boot loader
from.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The default host NQN, which is generated based on the host's UUID,
does not follow the UUID-based NQN format laid out in the NVMe 1.3
specification. Remove the "NVMf:" portion of the NQN to match the spec.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
This can cause issues with processes using the poll()
interface:
1) client sends two oneway transactions
2) the second one gets queued on async_todo
(because the server didn't handle the first one
yet)
3) server returns from poll(), picks up the
first transaction and does transaction work
4) server is done with the transaction, sends
BC_FREE_BUFFER, and the second transaction gets
moved to thread->todo
5) libbinder's handlePolledCommands() only handles
the commands in the current data buffer, so
doesn't see the new transaction
6) the server continues running and issues a new
outgoing transaction. Now, it suddenly finds
the incoming oneway transaction on its thread
todo, and returns that to userspace.
7) userspace does not expect this to happen; it
may be holding a lock while making the outgoing
transaction, and if handling the incoming
trasnaction requires taking the same lock,
userspace will deadlock.
By queueing the async transaction to the proc
workqueue, we make sure it's only picked up when
a thread is ready for proc work.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows userspace to request death notifications without
having to worry about getting an immediate callback on the same
thread; one scenario where this would be problematic is if the
death recipient handler grabs a lock that was already taken
earlier (eg as part of a nested transaction).
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because is_spin_locked() always returns false on UP
systems.
Use assert_spin_locked() instead, and remove the
WARN_ON() instances, since those were easy to verify.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BINDER_GET_NODE_DEBUG_INFO ioctl will return debug info on
a node. Each successive call reusing the previous return value
will return the next node. The data will be used by
libmemunreachable to mark the pointers with kernel references
as reachable.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of pushing new transactions to the process
waitqueue, select a thread that is waiting on proc
work to handle the transaction. This will make it
easier to improve priority inheritance in future
patches, by setting the priority before we wake up
a thread.
If we can't find a waiting thread, submit the work
to the proc waitqueue instead as we did previously.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes the process waitqueue, so that threads
can only wait on the thread waitqueue. Whenever
there is process work to do, pick a thread and
wake it up. Having the caller pick a thread is
helpful for things like priority inheritance.
This also fixes an issue with using epoll(),
since we no longer have to block on different
waitqueues.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the number of active, lru, and free pages for
each binder process in binder stats
Signed-off-by: Sherry Yang <sherryy@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix crash introduced by 74310e06be
(android: binder: Move buffer out of area shared with user space)
when close is called after open without mmap in between.
Reported-by: kernel test robot <fengguang.wu@intel.com>
Fixes: 74310e06be ("android: binder: Move buffer out of area shared with user space")
Signed-off-by: Sherry Yang <sherryy@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wf_sensor_ops structures are only stored in the ops field of a
wf_sensor structure, which is declared as const. Thus the
wf_sensor_ops structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct wf_sensor_ops i@p = { ... };
@ok1@
identifier r.i;
struct wf_sensor s;
position p;
@@
s.ops = &i@p
@ok2@
identifier r.i;
struct wf_sat_sensor s;
position p;
@@
s.sens.ops = &i@p
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct wf_sensor_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct wf_sensor_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
[mpe: Also convert the two cases inside #if 0]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds P9 NX support for 842 compression engine. Virtual
Accelerator Switchboard (VAS) is used to access 842 engine on P9.
For each NX engine per chip, setup receive window using
vas_rx_win_open() which configures RxFIFo with FIFO address, lpid,
pid and tid values. This unique (lpid, pid, tid) combination will
be used to identify the target engine.
For crypto open request, open send window on the NX engine for
the corresponding chip / cpu where the open request is executed.
This send window will be closed upon crypto close request.
NX provides high and normal priority FIFOs. For compression /
decompression requests, we use only hight priority FIFOs in kernel.
Each NX request will be communicated to VAS using copy/paste
instructions with vas_copy_crb() / vas_paste_crb() functions.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds changes for checking P9 specific 842 engine
error codes. These errros are reported in coprocessor status
block (CSB) for failures.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Send window is opened / closed for each crypto session.
So initializes txwin in workmem.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Updating coprocessor list is moved to nx842_add_coprocs_list().
This function will be used for both icswx and VAS functions.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move deleting coprocessors info upon exit or failure to
nx842_delete_coprocs().
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Configure CRB is moved to nx842_configure_crb() so that it can
be used for icswx and VAS exec functions. VAS function will be
added later with P9 support.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename nx842_powernv_function to nx842_powernv_exec.
nx842_powernv_exec points to nx842_exec_icswx and
will be point to VAS exec function which will be added later
for P9 NX support.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
bitmap_resize() does not work for file-backed bitmaps.
The buffer_heads are allocated and initialized when
the bitmap is read from the file, but resize doesn't
read from the file, it loads from the internal bitmap.
When it comes time to write the new bitmap, the bh is
non-existent and we crash.
The common case when growing an array involves making the array larger,
and that normally means making the bitmap larger. Doing
that inside the kernel is possible, but would need more code.
It is probably easier to require people who use file-backed
bitmaps to remove them and re-add after a reshape.
So this patch disables the resizing of arrays which have
file-backed bitmaps. This is better than crashing.
Reported-by: Zhilong Liu <zlliu@suse.com>
Fixes: d60b479d17 ("md/bitmap: add bitmap_resize function to allow bitmap resizing.")
Cc: stable@vger.kernel.org (v3.5+).
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
One of the two scsi-mq functions that requeue a request unprepares a
request before requeueing (scsi_io_completion()) but the other function
not (__scsi_queue_insert()). Make sure that a request is unprepared
before requeuing it.
Fixes: commit d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make these two member variables available in debugfs such that their
value can be verified by kernel developers. An example of the new
output:
ffff8804a513d480 {.op=READ, .cmd_flags=META|PRIO, .rq_flags=MQ_INFLIGHT|DONTPREP|IO_STAT|STATS, .atomic_flags=STARTED, .tag=17, .internal_tag=-1, .cmd=Read(10) 28 00 08 81 32 38 00 00 08 00, .retries=0, allocated 0.010 s ago}
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Requests are unprepared and reprepared when being requeued. Avoid that
requeuing resets .jiffies_at_alloc and .retries by initializing these
two member variables from inside scsi_initialize_rq() and by preserving
both member variables when preparing a request. This patch affects the
requeuing behavior of both the legacy scsi and the scsi-mq code paths.
Reported-by: Brian King <brking@linux.vnet.ibm.com>
References: https://lkml.org/lkml/2017/8/18/923 ("Re: [BUG][bisected 270065e] linux-next fails to boot on powerpc")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a pass-through request is submitted then blk_get_request()
initializes that request by calling scsi_initialize_rq(). Also call this
function for filesystem requests. Introduce CMD_INITIALIZED to keep
track of whether or not a request has already been initialized.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull block fixes from Jens Axboe:
"Unfortunately a few issues that warrant sending another pull request,
even if I had hoped to avoid it. This contains:
- A fix for multiqueue xen-blkback, on tear down / disconnect.
- A few fixups for NVMe, including a wrong bit definition, fix for
host memory buffers, and an nvme rdma page size fix"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix the definition of the doorbell buffer config support bit
nvme-pci: use dma memory for the host memory buffer descriptors
nvme-rdma: default MR page size to 4k
xen-blkback: stop blkback thread of every queue in xen_blkif_disconnect
Pull device mapper fixes from Mike Snitzer:
- A couple fixes for bugs introduced as part of the blk_status_t block
layer changes during the 4.13 merge window
- A printk throttling fix to use discrete rate limiting state for each
DM log level
- A stable@ fix for DM multipath that delays request requeueing to
avoid CPU lockup if/when the request queue is "dying"
* tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: do not lock up a CPU with requeuing activity
dm: fix printk() rate limiting code
dm mpath: retry BLK_STS_RESOURCE errors
dm: fix the second dec_pending() argument in __split_and_process_bio()
Don't populate the array seq on the stack, instead make it static.
Makes the object code smaller by over 1100 bytes:
Before:
text data bss dec hex filename
6152 1216 64 7432 1d08 drivers/input/mouse/byd.o
After:
text data bss dec hex filename
4974 1280 64 6318 18ae drivers/input/mouse/byd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The common code needs to export the probe and remove symbols in order
for the SMEM and RPM drivers to access them when compiled as a module.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
