NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pull crypto fixes from Herbert Xu:
"Fix an error path bug in ixp4xx as well as a read overrun in
sha1-avx2"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/sha1 - Fix reads beyond the number of blocks passed
crypto: ixp4xx - Fix error handling path in 'aead_perform()'
Add camera support to N900 dts. Also add a note about MMC & debugging.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra76-evm is a board based on TI's dra76 processor targeting
for infotainment systems. Adding support for this platform.
dra76-evm and dra7-evm has a similar layout except with few differences.
So create a dra7-evm-common.dtsi with similarities on dra76-evm and
dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 2 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding basic dts support for DRA76 family while reusing the
data available in dra7.dtsi, dra74x.dtsi.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for Moxa UC-8100-ME-T open platform
The UC-8100-ME-T computing platform is designed
for embedded data acquisition industrial applications
The features of UC-8100-ME-T series are:
* eMMC
* SPI flash
* SD slot
* 2x LAN
* 2 RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with USB signal
* USB host
* EEPROM
* TPM
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fix unit adress as suggested by Rob]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.
However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set default mode for vaudio, which may be left in standby mode
if the system is booted via kexec from Android.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All nodes inhert "interrupt-parent" property from root
node. Removed the aforementioned property from usbhsohci,
usbhsehci, ssi_port1, ssi_port2 nodes to avoid duplication.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for onboard gpio buzzer. It works using
the gpio-beeper driver. Pinmux entries for GPIO
controlling the buzzer are also added.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the missing 32-bit enable method for SMP on BCM2836 and
BCM2837. The BCM2837 already has an enabled method, but this one only
works for 64-bit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Eric Anholt <eric@anholt.net>
dra76-evm has LP87565. Enable it in omap2plus_defconfig.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Custom efuse powerdomain is always on in dra72 ES2.0
and dra76 SoCs. So register it as aon for these SoCs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
smp specific routines are called based on soc_is_*() api in omap-smc.c.
Add soc_is_dra76x() to the condition so that smp specific routines are
called for dra76 SoC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Certain IPs are available on dra76 which are not present
either in dra74 or dra72. So add provision to register dra76
specific IPs separately.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dummy patch to sort nodes alphabetically and add some blank lines
for consistency.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The bananapi-r2 board has an SD-card controller and built-in
EMMC storage so enables those devices in the devicetree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch enables these configs:
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
As example, a bluetooth device connected to UART port can be supported by
this.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable HiSilicon SAS controller based on PCI device,
which is included in hip08 SoC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
following ports:
- host 0 and 1 of CPM
- host 0 of CPS
These PHY are enabled by lanes coming from regulators based on two
I2C expanders.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add one PCIe host controller node for HiSilicon Hip07 SoC and enable it in
D05 board.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
If tracing is enabled and you get into xmon, the tracing buffer
continues to be updated, causing possible loss of data and unnecessary
tracing information coming from xmon functions.
This patch simple disables tracing when entering xmon, and re-enables it
if the kernel is resumed (with 'x').
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current xmon 'dt' command dumps the tracing buffer for all the CPUs,
which makes it very hard to read due to the fact that most of
powerpc machines currently have many CPUs. Other than that, the CPU
lines are interleaved in the ftrace log.
This new option just dumps the ftrace buffer for the current CPU.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is not called with the nest_init_lock held, and it also
unlocks the nest_init_lock immediately below, so it's fairly clear
that this is a typo and should be locking the lock.
Fixes: 885dcd709b ("powerpc/perf: Add nest IMC PMU support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 968159c003 ("powerpc/8xx: Getting rid of remaining use of
CONFIG_8xx") removed all but 2 references to 8xx in Kconfigs.
This patch removes the two remaining ones.
Fixes: 968159c003 ("powerpc/8xx: Getting rid of remaining use of CONFIG_8xx")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Allwinner A64 SoC is paired with the X-Powers AXP803 PMIC over the
Reduced Serial Bus (RSB). The regulators of this PMIC supply all power
rails of the SoC and many external peripherals.
Enable the driver for the regulators of this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner A64 SoC is paired with the X-Powers AXP803 PMIC over the
Reduced Serial Bus (RSB).
Enable the driver for this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: Refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
