Pull ata fixes from Damien Le Moal:
- Disable link power management on yet another misbehaving WD drive
(Niklas)
- Fix a use after free issue in the pata_sl82c105 driver (Hongyan)
* tag 'ata-7.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: pata_sl82c105: fix bridge revision use-after-free
ata: libata-core: Disable LPM on WDC WD141KFGX-68FH9N0
pci_get_slot() returns a referenced PCI device. Commit 44c10138fd
("PCI: Change all drivers to use pci_device->revision") replaced a
configuration-space read with direct access to the cached revision field,
but left that access after pci_dev_put(). The bridge may therefore be freed
before its revision is read.
Read the revision before dropping the reference.
Fixes: 44c10138fd ("PCI: Change all drivers to use pci_device->revision")
Signed-off-by: Hongyan Xu <getshell@seu.edu.cn>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Pull ata fixes from Damien Le Moal:
- Fix PCI resource initialization in the sata_mv driver to keep legacy
Marvell boards functional (Rosen)
- Fix ahci_ceva driver initialization error path (Radhey)
- Fix libata header file to remove a kernel doc compilation warning
(Randy)
- Increase the timeout for the STANDBY IMMEDIATE command to avoid
suspend failures with drives that are slow to respond to this command
(Matt)
- Fixes for the handling of timed out commands in the presence of
deferred non-NCQ commands, to avoid excessive delays in executing the
error handler (me)
- Disable link power management for a couple of WD drives that have
been identified as not functioning properly when power management is
used (Niklas)
- Fix the device iteration loop when checking for link power management
support to correctly handle port multiplier setups (Niklas)
* tag 'ata-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-sata: fix ata_scsi_lpm_supported() iteration
ata: libata-core: Disable LPM on WD Green 2.5 480GB
ata: libata-core: Disable LPM on some WD drives
scsi: libsas: terminate deferred commands on time out
ata: libata-scsi: schedule deferred atapi command
ata: libata-scsi: terminate deferred commands on time out
ata: libata-eh: Increase STANDBY IMMEDIATE timeout
ata: libata: avoid kernel-doc warnings
ata: ahci_ceva: fix error paths in ceva_ahci_platform_enable_resources()
ata: sata_mv: accept 1 or 2 resources in platform probe
The inner loop of ata_scsi_lpm_supported() uses the wrong variable when
iterating.
It should obviously use the link that we are currently iterating over,
rather than always using the host link.
ata_scsi_lpm_supported() is used to control if a user should be allowed
to change lpm policy (from the default) via sysfs.
Thus, this bug could potentially disallow users to change the LPM policy
for certain SATA devices via sysfs.
Cc: stable@vger.kernel.org
Fixes: 0060beec0b ("ata: libata-sata: Add link_power_management_supported sysfs attribute")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Link: https://lore.kernel.org/linux-ide/20260728112200.B99F21F000E9@smtp.kernel.org/
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
If a command times out while we have deferred non-NCQ commands waiting to
be issued, the SCSI EH task is not immediately woken up as the waiting
deferred commands are never issued nor completed, thus leaving the SCSI
host in a busy state (shost->host_failed != scsi_host_busy(shost)) which
prevents the SCSI EH task from being woken up. Eventually, when the
deferred commands also time out, the SCSI EH task is woken up and the
timeout processing occurs.
Avoid this unnecessary additional SCSI EH wake up time with the same
method as implemented in libata-scsi, using the eh_timed_out SCSI host
template operation. The function sas_eh_timed_out() implements this
operation and executes the function ata_scsi_retry_deferred_qc()
for SATA devices.
Co-developed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Tested-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify atapi_qc_complete() to call ata_scsi_schedule_deferred_qc() to
ensure that any deferred queued command can execute. This is similar to
ata_scsi_qc_complete() function for regular ATA devices.
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
If a command times out while we have deferred non-NCQ commands waiting to
be issued, the SCSI EH task is not immediately woken up as the waiting
deferred commands are never issued nor completed, thus leaving the SCSI
host in a busy state (shost->host_failed != scsi_host_busy(shost)) which
prevents the SCSI EH task from being woken up. Eventually, when the
deferred commands also time out, the SCSI EH task is woken up and the
timeout processing occurs.
Avoid this unnecessary SCSI EH task wake-up additional time by scheduling
a retry of all waiting deferred QCs, using the eh_timed_out SCSI host
template operation. The function ata_scsi_eh_timed_out() is introduced to
implement this operation.
However, terminating deferred commands with DID_REQUEUE to force a retry
by calling the function ata_scsi_requeue_deferred_qc() may still keep the
SCSI host in a busy state because the block layer may immediately re-issue
these commands. The solution to this is to schedule libata EH for the
port which suffered the command timeout to prevent accepting any new
command. ata_scsi_requeue_deferred_qc() is modified to add a call to
ata_port_schedule_eh() for this purpose.
In addition to this change, ata_scsi_requeue_deferred_qc() is also
modified to take a new timedout_scmd scsi command argument which indicates
the SCSI command that timed out. With this additional argument,
ata_scsi_requeue_deferred_qc() can now also terminate with DID_TIME_OUT
any timed out deferred qc, which simplifies ata_scsi_cmd_error_handler().
In this case, ata_scsi_requeue_deferred_qc() returns SCSI_EH_DONE, with
this return value propagated back to the ata_scsi_eh_timed_out() operation
to indicate to scsi_timeout() that the timed out command was handled and
no further processing is needed.
For non-timed out deferred qc that need to be retried,
ata_scsi_requeue_deferred_qc() returns SCSI_EH_NOT_HANDLED, thus
indicating to scsi_timeout() that the timed out command needs to go
through the SCSI EH (and libata EH) processing by adding it to the EH work
queue with scsi_eh_scmd_add().
One side effect of these changes is that the function atapi_qc_complete()
needs to be modified to ensure that a deferred ATAPI command that needs
to be retried is completed with DID_REQUEUE instead of the default
SAM_STAT_GOOD status, and a command that timed out is completed with
DID_TIME_OUT instead of SAM_STAT_CHECK_CONDITION.
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Tested-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a previous change (see Fixes) which reduced the standby timeout
from 30 to 5 seconds. Increase it to 15 seconds.
I was troubleshooting an error spotted during system suspend:
[ 1217.152867] ata1.00: Entering standby power mode
[ 1222.322948] ata1.00: qc timeout after 5000 msecs (cmd 0xe0)
[ 1222.324010] ata1.00: STANDBY IMMEDIATE failed (err_mask=0x4)
This drive is a Samsung 870 EVO SSD in good SMART standing, and I wasn't
aware of any reason it should be taking so long to standby. The issue is
intermittent, but I observed it sometimes taking 7 seconds to manually
standby. I assume this was interruption of background maintenance after
a power outage.
As a desktop user, I would prefer to wait the extra 2 seconds at suspend
to let the drive finish its business rather than drop the rails from
under it.
The change from 30 to 5 seconds was implicit when switching suspend
from START STOP UNIT to an internal command with no timeout table entry.
No reason was stated for the change.
Fixes: aa3998dbeb ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Assisted-by: Claude:claude-5-fable
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
On phy_init() failure the error path fallsthrough to disable_rsts, which
deasserts the controller reset and then enters disable_phys calling
phy_power_off() on PHYs that were never powered on. That corrupts the PHY
power_count and triggers an extra runtime PM put.
Use a separate exit_phys path that unwinds with phy_exit() only and falls
through to disable_clks while the controller remains in reset. Reserve
phy_power_off() for the phy_power_on() failure path only, and skip
masked-out ports in both unwind loops.
On phy_power_on() failure re-assert the controller reset before disabling
clocks and regulators, matching the teardown order used by
ahci_platform_enable_resources() and ahci_platform_disable_resources().
Fixes: 26c8404e16 ("ata: ahci_ceva: fix error handling for Xilinx GT PHY support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Board files in arch/arm/plat-orion, arch/arm/mach-dove,
arch/arm/mach-mv78xx0 and arch/arm/mach-orion5x still register the
"sata_mv" device with two resources (IORESOURCE_MEM plus IORESOURCE_IRQ).
Those devices are rejected with -EINVAL, so SATA no longer probes on
legacy Marvell Orion/Kirkwood-style boards.
Accept both 1 resource (DT, IRQ fetched via platform_get_irq()) and 2
resources (legacy, IRQ supplied as a second resource) so both probing
paths work.
Fixes: b3b2bec964 ("ata: sata_mv: Fixes expected number of resources now IRQs are gone")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Pull ata fixes from Damien Le Moal:
- Interrupt initialization and handling fixes for the Designware
ahci_dwc driver (Rosen)
- Avoid possible infinite loop when scanning completion in the
Designware ahci_dwc driver (Rosen)
* tag 'ata-7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning
ata: sata_dwc_460ex: fix clear_interrupt_bit() clearing all pending interrupts
ata: sata_dwc_460ex: use platform_get_irq()
ata: sata_dwc_460ex: enable SATA interrupts only after IRQ handler is registered
The hand-rolled bit-scanning loop in the NCQ completion path has an
infinite loop bug. When tag_mask has only high bits set (e.g.
0x80000000), the inner while loop left-shifts tag_mask until it
overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1
stays 0, causing an infinite loop in hardirq context with a spinlock
held.
Replace the open-coded bit-scanning with __ffs() which correctly
finds the least significant set bit and is bounded by the width of
the argument.
Fixes: 62936009f3 ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
clear_interrupt_bit() ignores the bit argument and performs a
read-write-back of the entire INTPR register. If INTPR uses standard
Write-1-to-Clear semantics, this clears every pending interrupt bit,
not just the intended one. Coalesced interrupts (e.g. DMAT + NEWFP)
would be cleared together, silently losing the second event.
Write only the specific bit to clear so that other pending interrupts
are preserved.
Fixes: 62936009f3 ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Replace irq_of_parse_and_map() with platform_get_irq() in both
sata_dwc_dma_init_old() and sata_dwc_probe(). This is the preferred
way to obtain IRQs for platform devices and provides better error
reporting. Remove the now-unnecessary #include <linux/of_irq.h>.
irq_of_parse_and_map() requires irq_dispose_mapping(), which is missing.
Also fix unused variable when CONFIG_SATA_DWC_OLD_DMA is disabled.
Fixes: 62936009f3 ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
sata_dwc_enable_interrupts() is called before platform_get_irq() and
ata_host_activate(), leaving the SATA controller's interrupt mask
enabled without a registered handler. If a later step fails (irq
request, phy init, etc.) or if the controller asserts an interrupt
during probe, the irq line may fire with no handler, causing a
spurious interrupt storm.
Move sata_dwc_enable_interrupts() after ata_host_activate() so that
interrupts are only unmasked once the handler is registered and the
core is fully initialized.
Fixes: 62936009f3 ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Pull ata fixes from Damien Le Moal:
- Fix handling of security locked drive revalidation. This prevents
such drives from being dropped when locked on resume (Terrence)
* tag 'ata-7.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: Allow capacity transition to zero for locked drives
ata: libata-core: Skip HPA resize for locked drives
Commit 91842ed844 ("ata: libata-core: Set capacity to zero for a
security locked drive") introduced setting the device capacity (n_sectors)
to zero in ata_dev_configure() if the drive is security locked.
However, during runtime revalidation, ata_dev_revalidate() compares the
new capacity (now 0) with the old capacity (>0) and detects a mismatch.
Since it does not consider the locked status, it returns -ENODEV.
This revalidation failure can occur when doing a reset of the PHY (e.g.
hard reset) for a controller that has I/Os in flight. The timed out
I/Os trigger the SCSI Error Handling (EH) path, which in turn invokes
libata device revalidation. If the drive is locked at runtime (e.g.
it lost power during reset and relocked), revalidation sees the capacity
transition to zero and fails, eventually disabling the device.
Fix this by allowing the capacity transition to zero in
ata_dev_revalidate() if the drive is reported as security locked by
ata_id_is_locked().
Fixes: 91842ed844 ("ata: libata-core: Set capacity to zero for a security locked drive")
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Terrence Adams <tadamsjr@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Skip HPA resize in ata_hpa_resize() if the drive is security locked.
If the drive is locked, the command to read the native max address
fails with -EACCES, which currently causes the sticky quirk
ATA_QUIRK_BROKEN_HPA to be set on the device.
Setting this sticky quirk causes subsequent revalidations (after the
drive is unlocked) to bypass HPA checks, preventing the unlocked drive
from exposing its full native capacity without a reboot or device removal.
Cc: stable@vger.kernel.org
Signed-off-by: Terrence Adams <tadamsjr@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Pull mod_devicetable.h header split from Uwe Kleine-König:
"Split <linux/mod_devicetable.h> in per subsystem headers
<linux/mod_devicetable.h> is included transitively in nearly every
driver in an x86_64 allmodconfig build of v7.1:
$ find drivers -name \*.o -not -name \*.mod.o | wc -l
21330
$ find drivers -name \*.o.cmd -not -name \*.mod.o.cmd | xargs grep -l mod_devicetable.h | wc -l
17038
The result of this mixture of different and unrelated subsystem
details is that even when touching an obscure device id struct most of
the kernel needs to be recompiled. Given that each driver typically
only needs one or two of these structures, splitting into per
subsystem headers and only including what is really needed reduces the
amount of needed recompilation.
This split is implemented in the first commit and then after some
preparatory work in the following commits, the last two replace
includes of <linux/mod_devicetable.h> by the actually needed more
specific headers.
There are still a few instances left, but the ones with high impact
(that is in headers that are used a lot) and the easy ones (.c files)
are handled. These remaining includes will be addressed during the
next merge window"
* tag 'device-id-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
Replace <linux/mod_devicetable.h> by more specific <linux/device-id/*.h> (c files)
Replace <linux/mod_devicetable.h> by more specific <linux/device-id/*.h> (headers)
parisc: #include <linux/compiler.h> for unlikely() in <asm/ptrace.h>
media: em28xx: Add include for struct usb_device_id
LoongArch: KVM: Add include defining struct cpu_feature
ALSA: hda/core: Add include defining struct hda_device_id
usb: dwc2: Add include defining struct pci_device_id
platform/x86: int3472: Add include defining struct dmi_system_id
platform/x86: x86-android-tablets: Add include defining struct dmi_system_id
i2c: Let i2c-core.h include <linux/i2c.h>
of: Explicitly include <linux/types.h> and <linux/err.h>
platform/x86: msi-ec: Ensure dmi_system_id is defined
usb: serial: Include <linux/usb.h> in <linux/usb/serial.h>
driver core: platform: Include header for struct platform_device_id
driver: core: Include headers for acpi_device_id and of_device_id for struct device_driver
media: ti: vpe: #include <linux/platform_device.h> explicitly
mod_devicetable.h: Split into per subsystem headers
The function ata_scsi_rbuf_fill() is used to copy the response of
emulated SCSI commands from ata_scsi_rbuf to the SCSI command's
scatterlist.
Currently, sg_copy_from_buffer() is called with the size argument
set to ATA_SCSI_RBUF_SIZE (2048 bytes). Since ata_scsi_rbuf is
zeroed out before the simulation actor is invoked, copying the
full buffer size causes the remainder of the SCSI command's
transfer buffer (beyond the actual response length 'len') to be
overwritten with zeroes. This clobbers any pre-existing sentinel
values or data in the caller's buffer tail, even though the
correct residual count is reported via scsi_set_resid().
Fix this by passing the actual response length 'len' as the copy
size to sg_copy_from_buffer(), ensuring that the tail of the
caller's buffer remains untouched. Also, add a defensive check
to ensure that the actor does not return a length exceeding the
static buffer capacity. If this occurs, trigger a WARN_ON(),
fail the command with an aborted command error, and return
immediately without copying any data.
The fix was tested by invoking an SCSI SG_IO INQUIRY on
an ATA disk on vanilla build, and build with the fix. Confirmed
that the input buffer's tail end remains unmodified with the fix.
Fixes: 5251ae224d ("ata: libata-scsi: Return residual for emulated SCSI commands")
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Karuna Ramkumar <rkaruna@google.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
When dmaengine_slave_config() fails, the DMA channel acquired by
dma_request_chan() is not released before returning the error,
leaking the channel reference.
Fix by adding dma_release_channel() in the error path.
The ata_host_activate() error path already correctly releases the
DMA channel.
Cc: stable@vger.kernel.org
Fixes: 88622d80af ("ata: pata_pxa: dmaengine conversion")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
gemini_sata_bridge_init() prepares and enables both SATA PCLKs, then
disables them again while keeping the clocks prepared for later bridge
start and stop operations. If gemini_setup_ide_pins() fails after that,
gemini_sata_probe() returns directly and skips the existing
out_unprep_clk unwind path.
Route the IDE pinctrl failure through out_unprep_clk so the clocks
prepared by gemini_sata_bridge_init() are unprepared before probe
fails.
Fixes: d872ced29d ("ata: sata_gemini: Introduce explicit IDE pin control")
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
ata_dev_config_cpr() takes the number of range descriptors from buf[0]
of the concurrent positioning ranges log (up to 255), which the device
reports independently of the log size in the GPL directory. The count is
then walked at a fixed 32-byte stride in two places with no bound: the
log read here, and the INQUIRY VPD page B9h emitter, which writes one
descriptor per range into the fixed 2048-byte ata_scsi_rbuf. A device
reporting a count larger than its own log overflows the read buffer (up
to 7704 bytes past a 512-byte slab), and a count above 62 overflows the
response buffer on the emit side.
Bound the count once, on probe, against both the log the device returned
and the number of descriptors the VPD B9h response buffer can hold
(ATA_DEV_MAX_CPR, derived from the rbuf size). Reject an out-of-range
count with a warning; this keeps the emitter in bounds with no separate
change there.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Fixes: fe22e1c2f7 ("libata: support concurrent positioning ranges log")
Fixes: c745dfc541 ("libata: fix reading concurrent positioning ranges log")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
The PNY CS900 1TB SSD (Phison PS3111-S11, DRAM-less) drops off the bus
after entering Device-Initiated Slumber during idle. With the default
med_power_with_dipm policy the link goes down (SStatus 1 SControl 300)
and does not recover, forcing the filesystem read-only. Forcing
max_performance keeps the link stable across prolonged idle.
Add a NOLPM quirk so link power management is disabled for this drive
specifically, leaving it intact for other devices on the host.
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Pull ata updates from Niklas Cassel:
- Bump required Clang version to 23 (Marco), and add Clang context
analysis annotations (Bart)
- Use the ahci_nr_ports() helper in libahci (me)
- Fail to probe the ahci driver if the BAR size is smaller than the
required size to support CAP.NP (Number of Ports) (liyouhong)
- Move EXPORT_SYMBOL_GPL(ahci_do_softreset) to be just below the
function definition (Bart)
- Make ata_scsi_scan_host() schedule hotplug work on the
system_dfl_long_wq workqueue so that it can benefit from scheduler
task placement (Marco)
- Make ata_scsi_port_error_handler() schedule hotplug work on the
system_dfl_long_wq workqueue, such that the work always uses the same
workqueue (me)
- Use devm_platform_get_and_ioremap_resource() in pata_arasan_cf driver
(Rosen)
- Fix ata_exec_internal() to only release and acquire the EH mutex if
the calling function is the one holding the EH mutex (Bart)
- Use hweight_long() to count the port_map bits (TanZheng)
- Add COMPILE_TEST support for pata_ep93xx driver (Rosen)
- Drop unused assignments from pata_isapnp driver (Uwe)
- Extend existing JMicron PMP quirk to include JMicron JMS562 (Xu)
- Drop unused assignments of pci_device_id driver data (Uwe)
- Use named initializers for pci_device_id arrays (Uwe)
* tag 'ata-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: Use named initializers for pci_device_id arrays
ata: Drop unused assignments of pci_device_id driver data
ata: libata-pmp: add JMicron JMS562 quirk
ata: pata_isapnp: Drop unused assignments from pnp_device_id array
ata: pata_ep93xx: add COMPILE_TEST support
ata: pata_ep93xx: use unsigned long for data
ata: pata_ep93xx: avoid asm on non ARM
ata: Annotate functions in the issuing path with __must_hold()
ata: libata: Pass ap parameter directly to functions in the issuing path
ata: libata: Document when host->eh_mutex should be held
ata: libata: Add an argument to ata_eh_reset()
ata: ahci: use hweight_long() to count port_map bits
ata: libata: Fix ata_exec_internal()
ata: pata_arasan_cf: simplify ioremap
ata: libata-eh: queue hotplug work on the system_dfl_long_wq workqueue
ata: libata-scsi: Move long delayed work on system_dfl_long_wq
ata: ahci: Move EXPORT_SYMBOL_GPL(ahci_do_softreset)
ata: ahci: fail probe if BAR too small for claimed ports
ata: libahci: use ahci_nr_ports() helper
Pull SoC driver updates from Arnd Bergmann:
"There are a few added drivers, but mostly the normal maintenance to
drivers for firmware, memory controller and other soc specific
hardware:
- The NXP QuickEngine gets modern MSI support, which allows some
cleanups to the GICv3 irqchip chip driver
- A new SoC specific driver for the Renesas R-Car MFIS unit is added,
encapsulating support for the on-chip mailbox and hwspinlock
implementations that are not easily separated into individual
drivers
- The Qualcomm SoC drivers add support for additional SoC
implementations, and flexibility around power management for the
serial-engine driver as well as probing the LLCC driver using
custom hardware descriptions inside of the device itself.
- Added support for the Samsung thermal management unit
- A cleanup to the Tegra 'PMC' driver interfaces to remove legacy
APIs and allow multiple PMC instances everywhere.
- Updates to the TI SCI and KNAS drivers to improve suspend/resume
support.
- Minor driver changes for mediatek, xilinx, allwinner, aspeed,
tegra, broadcom, amd, microchip and starfive specific drivers
- Memory controller updates for Tegra and Renesas for additional SoC
types and other improvements.
- Firmware driver updates for Arm FF-A, SMCCC and SCMI interfaces, to
update driver probing, object lifetimes and address minor bugs"
* tag 'soc-drivers-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
Revert "firmware: zynqmp: Add dynamic CSU register discovery and sysfs interface"
Revert "Documentation: ABI: add sysfs interface for ZynqMP CSU registers"
memory: tegra234: drop dead NULL check in tegra234_mc_icc_aggregate()
memory: tegra264: drop redundant tegra264_mc_icc_aggregate()
memory: tegra186-emc: stop borrowing MC aggregate hook for EMC
soc: aspeed: cleanup dead default for ASPEED_SOCINFO
firmware: tegra: bpmp: Add support for multi-socket platforms
firmware: tegra: bpmp: Propagate debugfs errors
soc/tegra: pmc: Add Tegra238 support
soc/tegra: pmc: Restrict power-off handler to Nexus 7
soc/tegra: pmc: Populate powergate debugfs only when needed
soc/tegra: pmc: Move legacy code behind CONFIG_ARM guard
soc/tegra: pmc: Remove unused legacy functions
soc/tegra: pmc: Create PMC context dynamically
firmware: samsung: acpm: remove compile-testing stubs
firmware: samsung: acpm: Add devm_acpm_get_by_phandle helper
firmware: samsung: acpm: Add TMU protocol support
firmware: samsung: acpm: Make acpm_ops const and access via pointer
firmware: samsung: acpm: Drop redundant _ops suffix in acpm_ops members
firmware: samsung: acpm: Annotate rx_data->cmd with __counted_by_ptr
...
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
pci_device_id that replaces .driver_data by an anonymous union.
Also drop the comma after a few list terminators.
This patch doesn't modify the compiled array, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The drivers explicitly set the .driver_data member of struct
pci_device_id to zero without relying on that value. Drop these unused
assignments.
While touching these arrays, convert the one driver not using PCI_DEVICE
to use that macro and align the array's coding style to what is used
most for these. (i.e. break very long lines, a single space in the list
terminator and no trailing comma.)
This patch doesn't modify the compiled array, only its representation in
source form benefits. The former was confirmed with builds on x86 and
arm64.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
JMicron JMS562, as used in QNAP QDA-A2AR RAID1 adapters, may
keep the exported ATA device not ready while the array is rebuilding.
In this state, libata may repeatedly try to softreset and classify
the fan-out link. On the affected adapter, this can time out, make
PMP/SCR access fail, and eventually disable the fan-out link before
the RAID volume is exported.
A failing boot shows the fan-out link failing SRST, PMP access
timing out, SCR read failing, and the link being disabled:
ata4.00: softreset failed (device not ready)
ata4.15: qc timeout after 3000 msecs (cmd 0xe4)
ata4.00: failed to read SCR 0 (Emask=0x4)
ata4.00: failed to recover link after 3 tries, disabling
After that, the root filesystem on the exported RAID volume cannot
be found.
Add JMS562 to the existing JMicron PMP quirk that disables LPM,
avoids softreset on fan-out links, and assumes an ATA device. This
prevents libata from dropping the exported RAID volume during rebuild
recovery.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Explicitly assigning .driver_data in drivers that don't use this member
is silly and a bit irritating. Drop it. Also simplify the list
terminator entry to be just empty to match what most other device_id
tables do.
There is no changed semantic, not even a change in the compiled result.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
soc/tegra: pmc: Changes for v7.2-rc1
The bulk of these changes converts existing users to the modern variants
of the API that take a PMC instance as argument. This completes the
transition to multi-instance support, which then makes room for cleanups
and restricting the remaining legacy APIs to 32-bit platforms.
Some changes in this set also clean up powergate debugfs and restrict
the power-off handler to be installed only where appropriate. Lastly,
support for Tegra238 is added.
* tag 'tegra-for-7.2-pmc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add Tegra238 support
soc/tegra: pmc: Restrict power-off handler to Nexus 7
soc/tegra: pmc: Populate powergate debugfs only when needed
soc/tegra: pmc: Move legacy code behind CONFIG_ARM guard
soc/tegra: pmc: Remove unused legacy functions
soc/tegra: pmc: Create PMC context dynamically
usb: xhci: tegra: Explicitly specify PMC instance to use
PCI: tegra: Explicitly specify PMC instance to use
media: vde: Explicitly specify PMC instance to use
drm/tegra: Explicitly specify PMC instance to use
drm/nouveau: tegra: Explicitly specify PMC instance to use
ata: ahci_tegra: Explicitly specify PMC instance to use
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the build failures have been fixed, we can add COMPILE_TEST so
the buildbots can find potentially more problems.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
An int is being encoded as a void pointer but that breaks on 64-bit
systems as the type needs to match pointer size.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The raw ARM asm delay loop prevents COMPILE_TEST builds on
non-ARM architectures. Guard it with CONFIG_ARM and provide a
cpu_relax() fallback for compilation on other architectures.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Annotate the following functions used in the issuing path:
ata_qc_issue(), ata_sas_queuecmd(), ata_scsi_qc_issue(),
ata_scsi_translate(), __ata_scsi_queuecmd()
These functions are all used in the issuing path, so context analysis will
be able to verify that the ap lock is held, from it is taken in
sas_queuecommand() or ata_scsi_queuecmd() all the way down to
ata_qc_issue().
Commenting out the spin_lock_irqsave() successfully results in a compiler
error on Clang 23.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Context analysis cannot recognize that qc->ap == ap.
Therefore, grow a struct ata_port parameter to the following functions:
ata_qc_issue(), __ata_scsi_queuecmd(), and ata_scsi_translate()
such that we will be able to enable context analysis in a follow-up commit.
No functionality has been changed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Annotate the following functions with __must_hold(&host->eh_mutex):
* All ata_port_operations.error_handler() implementations.
* ata_eh_reset() and ata_eh_recover() because these functions call
ata_eh_release() and ata_eh_acquire().
* All callers of ata_eh_reset() and ata_eh_recover().
Enable Clang's context analysis. This will cause the build to fail if
e.g. a locking bug would be introduced in an error path. This patch
should not affect the generated assembler code.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[cassel: drop note about clang 23 from commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Pass the ATA port pointer as first argument to ata_eh_reset(). No
functionality has been changed. This patch prepares for enabling lock
context analysis. Without this patch, lockdep_assert_held() statements
would have to be added before each ata_eh_reset() call because the
compiler doesn't know that ap->link.p == ap. See also ata_link_init().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Replace the open loop used to calculate the number of set bits
in the port mapping with the `hweight_long()` function, which
simplifies the code without altering its functionality.
Signed-off-by: TanZheng <tanzheng@kylinos.cn>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Some but not all ata_exec_internal() calls happen from the context of
the ATA error handler. Commit c0c362b60e ("libata: implement cross-port
EH exclusion") added ata_eh_release() and ata_eh_acquire() calls in
ata_exec_internal(). Calling these functions is necessary if the caller
holds the eh_mutex but is not allowed if the caller doesn't hold that
mutex. Fix this by only calling ata_eh_release() and ata_eh_acquire() if
the caller holds the eh_mutex. An example of an indirect caller of
ata_exec_internal() that does not hold the eh_mutex is
ata_host_register().
Fixes: c0c362b60e ("libata: implement cross-port EH exclusion")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Use devm_platform_get_and_ioremap_resource() to combine
platform_get_resource, request_mem_region, and ioremap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
ata_scsi_port_error_handler() uses schedule_delayed_work() to queue
the ap->hotplug_task work.
schedule_delayed_work() always uses the system_percpu_wq per-cpu
workqueue.
ata_scsi_scan_host() queues the ap->hotplug_task work on the unbound
system_dfl_long_wq workqueue.
It seems counter-intuitive to queue the same work on two different
workqueues. Thus, change ata_scsi_port_error_handler() to also queue
the ap->hotplug_task work on the system_dfl_long_wq workqueue, such
that the work is always queued on the same workqueue.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Currently the code enqueue work items using {queue|mod}_delayed_work(),
using system_long_wq. This workqueue should be used when long works are
expected, but it is a per-cpu workqueue.
This is important because queue_delayed_work() queue the work using:
queue_delayed_work_on(WORK_CPU_UNBOUND, ...);
Note that WORK_CPU_UNBOUND = NR_CPUS.
This would end up calling __queue_delayed_work() that does:
if (housekeeping_enabled(HK_TYPE_TIMER)) {
// [....]
} else {
if (likely(cpu == WORK_CPU_UNBOUND))
add_timer_global(timer);
else
add_timer_on(timer, cpu);
}
So when cpu == WORK_CPU_UNBOUND the timer is global and is
not using a specific CPU. Later, when __queue_work() is called:
if (req_cpu == WORK_CPU_UNBOUND) {
if (wq->flags & WQ_UNBOUND)
cpu = wq_select_unbound_cpu(raw_smp_processor_id());
else
cpu = raw_smp_processor_id();
}
Because the wq is not unbound, it takes the CPU where the timer
fired and enqueue the work on that CPU.
The consequence of all of this is that the work can run anywhere,
depending on where the timer fired.
Recently, a new unbound workqueue specific for long running work has
been added:
c116737e97 ("workqueue: Add system_dfl_long_wq for long unbound works")
So change system_long_wq with system_dfl_long_wq so that the work may
benefit from scheduler task placement.
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
From Documentation/process/coding-style.rst:
In source files, separate functions with one blank line. If the function
is exported, the **EXPORT** macro for it should follow immediately after
the closing function brace line.
Hence, move EXPORT_SYMBOL_GPL(ahci_do_softreset) to just below the
definition of the ahci_do_softreset() function.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
When an AHCI controller is disabled in BIOS, its HOST_CAP register may
contain a bogus value, e.g. 0xFFFFFFFF.
Since CAP.NP (Number of Ports) is a zeroes based 5-bit register field,
a value of 0x1f means 32 ports. If CAP.NP claims more ports than can
physically fit within the mapped BAR region, accessing port registers
beyond the BAR boundary causes a kernel panic.
Add validation in ahci_init_one() to check that the BAR size is
sufficient for the number of ports claimed in CAP.NP. The check
calculates the required MMIO size as:
required_size = 0x100 (global registers) + max_ports * 0x80
If required_size exceeds the actual BAR size, the probe fails with
-ENODEV, preventing the panic and providing a clear error message.
Reported-by: liyouhong <liyouhong@kylinos.cn>
Closes: https://lore.kernel.org/all/20260422080322.1006592-1-dayou5941@163.com/
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: liyouhong <liyouhong@kylinos.cn>
[cassel: commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Use ahci_nr_ports() helper instead of open coding the same.
No functional change.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
