Almost all validation logic is in the drivers, but they are
missing reliable way to convey failure reason to userspace
applications.
Let's use extack to return this information to users.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethtool_aggregate_*_stats() are implemented in net/ethtool/stats.c, a
file which is compiled out when CONFIG_ETHTOOL_NETLINK=n. In order to
avoid adding Kbuild dependencies from drivers (which call these helpers)
on CONFIG_ETHTOOL_NETLINK, let's add some shim definitions which simply
make the helpers dead code.
This means the function prototypes should have been located in
include/linux/ethtool_netlink.h rather than include/linux/ethtool.h.
Fixes: 449c545964 ("net: ethtool: add helpers for aggregate statistics")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230125110214.4127759-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are multiple ICMP rate limiting mechanisms:
* Global limits: net.ipv4.icmp_msgs_burst/icmp_msgs_per_sec
* v4 per-host limits: net.ipv4.icmp_ratelimit/ratemask
* v6 per-host limits: net.ipv6.icmp_ratelimit/ratemask
However, when ICMP output is limited, there is no way to tell
which limit has been hit or even if the limits are responsible
for the lack of ICMP output.
Add counters for each of the cases above. As we are within
local_bh_disable(), use the __INC stats variant.
Example output:
# nstat -sz "*RateLimit*"
IcmpOutRateLimitGlobal 134 0.0
IcmpOutRateLimitHost 770 0.0
Icmp6OutRateLimitHost 84 0.0
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Suggested-by: Abhishek Rawal <rawal.abhishek92@gmail.com>
Link: https://lore.kernel.org/r/273b32241e6b7fdc5c609e6f5ebc68caf3994342.1674605770.git.jamie.bainbridge@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Users who want to share a single public IP address for outgoing connections
between several hosts traditionally reach for SNAT. However, SNAT requires
state keeping on the node(s) performing the NAT.
A stateless alternative exists, where a single IP address used for egress
can be shared between several hosts by partitioning the available ephemeral
port range. In such a setup:
1. Each host gets assigned a disjoint range of ephemeral ports.
2. Applications open connections from the host-assigned port range.
3. Return traffic gets routed to the host based on both, the destination IP
and the destination port.
An application which wants to open an outgoing connection (connect) from a
given port range today can choose between two solutions:
1. Manually pick the source port by bind()'ing to it before connect()'ing
the socket.
This approach has a couple of downsides:
a) Search for a free port has to be implemented in the user-space. If
the chosen 4-tuple happens to be busy, the application needs to retry
from a different local port number.
Detecting if 4-tuple is busy can be either easy (TCP) or hard
(UDP). In TCP case, the application simply has to check if connect()
returned an error (EADDRNOTAVAIL). That is assuming that the local
port sharing was enabled (REUSEADDR) by all the sockets.
# Assume desired local port range is 60_000-60_511
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s.bind(("192.0.2.1", 60_000))
s.connect(("1.1.1.1", 53))
# Fails only if 192.0.2.1:60000 -> 1.1.1.1:53 is busy
# Application must retry with another local port
In case of UDP, the network stack allows binding more than one socket
to the same 4-tuple, when local port sharing is enabled
(REUSEADDR). Hence detecting the conflict is much harder and involves
querying sock_diag and toggling the REUSEADDR flag [1].
b) For TCP, bind()-ing to a port within the ephemeral port range means
that no connecting sockets, that is those which leave it to the
network stack to find a free local port at connect() time, can use
the this port.
IOW, the bind hash bucket tb->fastreuse will be 0 or 1, and the port
will be skipped during the free port search at connect() time.
2. Isolate the app in a dedicated netns and use the use the per-netns
ip_local_port_range sysctl to adjust the ephemeral port range bounds.
The per-netns setting affects all sockets, so this approach can be used
only if:
- there is just one egress IP address, or
- the desired egress port range is the same for all egress IP addresses
used by the application.
For TCP, this approach avoids the downsides of (1). Free port search and
4-tuple conflict detection is done by the network stack:
system("sysctl -w net.ipv4.ip_local_port_range='60000 60511'")
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_IP, IP_BIND_ADDRESS_NO_PORT, 1)
s.bind(("192.0.2.1", 0))
s.connect(("1.1.1.1", 53))
# Fails if all 4-tuples 192.0.2.1:60000-60511 -> 1.1.1.1:53 are busy
For UDP this approach has limited applicability. Setting the
IP_BIND_ADDRESS_NO_PORT socket option does not result in local source
port being shared with other connected UDP sockets.
Hence relying on the network stack to find a free source port, limits the
number of outgoing UDP flows from a single IP address down to the number
of available ephemeral ports.
To put it another way, partitioning the ephemeral port range between hosts
using the existing Linux networking API is cumbersome.
To address this use case, add a new socket option at the SOL_IP level,
named IP_LOCAL_PORT_RANGE. The new option can be used to clamp down the
ephemeral port range for each socket individually.
The option can be used only to narrow down the per-netns local port
range. If the per-socket range lies outside of the per-netns range, the
latter takes precedence.
UAPI-wise, the low and high range bounds are passed to the kernel as a pair
of u16 values in host byte order packed into a u32. This avoids pointer
passing.
PORT_LO = 40_000
PORT_HI = 40_511
s = socket(AF_INET, SOCK_STREAM)
v = struct.pack("I", PORT_HI << 16 | PORT_LO)
s.setsockopt(SOL_IP, IP_LOCAL_PORT_RANGE, v)
s.bind(("127.0.0.1", 0))
s.getsockname()
# Local address between ("127.0.0.1", 40_000) and ("127.0.0.1", 40_511),
# if there is a free port. EADDRINUSE otherwise.
[1] https://github.com/cloudflare/cloudflare-blog/blob/232b432c1d57/2022-02-connectx/connectx.py#L116
Reviewed-by: Marek Majkowski <marek@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The struct device for ISM devices was part of struct smcd_dev. Move to
struct ism_dev, provide a new API call in struct smcd_ops, and convert
existing SMCD code accordingly.
Furthermore, remove struct smcd_dev from struct ism_dev.
This is the final part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ism module had SMC-D-specific code sprinkled across the entire module.
We are now consolidating the SMC-D-specific parts into the latter parts
of the module, so it becomes more clear what code is intended for use with
ISM, and which parts are glue code for usage in the context of SMC-D.
This is the fourth part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We separate the code implementing the struct smcd_ops API in the ISM
device driver from the functions that may be used by other exploiters of
ISM devices.
Note: We start out small, and don't offer the whole breadth of the ISM
device for public use, as many functions are specific to or likely only
ever used in the context of SMC-D.
This is the third part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the smc module with the new ism device driver API.
This is the second part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new API that allows other drivers to concurrently access ISM devices.
To do so, we introduce a new API that allows other modules to register for
ISM device usage. Furthermore, we move the GID to struct ism, where it
belongs conceptually, and rename and relocate struct smcd_event to struct
ism_event.
This is the first part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conceptually, a DMB is a structure that belongs to ISM devices. However,
SMC currently 'owns' this structure. So future exploiters of ISM devices
would be forced to include SMC headers to work - which is just weird.
Therefore, we switch ISM to struct ism_dmb, introduce a new public header
with the definition (will be populated with further API calls later on),
and, add a thin wrapper to please SMC. Since structs smcd_dmb and ism_dmb
are identical, we can simply convert between the two for now.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regenerate the FOU uAPI header from the YAML spec.
The flags now come before attributes which use them,
and the comments for type disappear (coders should look
at the spec instead).
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kalle Valo says:
====================
wireless-next patches for v6.3
First set of patches for v6.3. The most important change here is that
the old Wireless Extension user space interface is not supported on
Wi-Fi 7 devices at all. We also added a warning if anyone with modern
drivers (ie. cfg80211 and mac80211 drivers) tries to use Wireless
Extensions, everyone should switch to using nl80211 interface instead.
Static WEP support is removed, there wasn't any driver using that
anyway so there's no user impact. Otherwise it's smaller features and
fixes as usual.
Note: As mt76 had tricky conflicts due to the fixes in wireless tree,
we decided to merge wireless into wireless-next to solve them easily.
There should not be any merge problems anymore.
Major changes:
cfg80211
- remove never used static WEP support
- warn if Wireless Extention interface is used with cfg80211/mac80211 drivers
- stop supporting Wireless Extensions with Wi-Fi 7 devices
- support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting
rfkill
- add GPIO DT support
bitfield
- add FIELD_PREP_CONST()
mt76
- per-PHY LED support
rtw89
- support new Bluetooth co-existance version
rtl8xxxu
- support RTL8188EU
* tag 'wireless-next-2023-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (123 commits)
wifi: wireless: deny wireless extensions on MLO-capable devices
wifi: wireless: warn on most wireless extension usage
wifi: mac80211: drop extra 'e' from ieeee80211... name
wifi: cfg80211: Deduplicate certificate loading
bitfield: add FIELD_PREP_CONST()
wifi: mac80211: add kernel-doc for EHT structure
mac80211: support minimal EHT rate reporting on RX
wifi: mac80211: Add HE MU-MIMO related flags in ieee80211_bss_conf
wifi: mac80211: Add VHT MU-MIMO related flags in ieee80211_bss_conf
wifi: cfg80211: Use MLD address to indicate MLD STA disconnection
wifi: cfg80211: Support 32 bytes KCK key in GTK rekey offload
wifi: cfg80211: Fix extended KCK key length check in nl80211_set_rekey_data()
wifi: cfg80211: remove support for static WEP
wifi: rtl8xxxu: Dump the efuse only for untested devices
wifi: rtl8xxxu: Print the ROM version too
wifi: rtw88: Use non-atomic sta iterator in rtw_ra_mask_info_update()
wifi: rtw88: Use rtw_iterate_vifs() for rtw_vif_watch_dog_iter()
wifi: rtw88: Move register access from rtw_bf_assoc() outside the RCU
wifi: rtl8xxxu: Use a longer retry limit of 48
wifi: rtl8xxxu: Report the RSSI to the firmware
...
====================
Link: https://lore.kernel.org/r/20230123103338.330CBC433EF@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core is in charge of the ethtool_ops of the net devices
associated with switch ports, so in case a hardware driver supports the
MAC merge layer, DSA must pass the callbacks through to the driver.
Add support for precisely that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We deliberately make the Linux UAPI pass the minimum fragment size in
octets, even though IEEE 802.3 defines it as discrete values, and
addFragSize is just the multiplier. This is because there is nothing
impossible in operating with an in-between value for the fragment size
of non-final preempted fragments, and there may even appear hardware
which supports the in-between sizes.
For the hardware which just understands the addFragSize multiplier,
create two helpers which translate back and forth the values passed in
octets.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a pMAC exists but the driver is unable to atomically query the
aggregate eMAC+pMAC statistics, the user should be given back at least
the sum of eMAC and pMAC counters queried separately.
This is a generic problem, so add helpers in ethtool to do this
operation, if the driver doesn't have a better way to report aggregate
stats. Do this in a way that does not require changes to these functions
when new stats are added (basically treat the structures as an array of
u64 values, except for the first element which is the stats source).
In include/linux/ethtool.h, there is already a section where helper
function prototypes should be placed. The trouble is, this section is
too early, before the definitions of struct ethtool_eth_mac_stats et.al.
Move that section at the end and append these new helpers to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3-2018 clause 99 defines a MAC Merge sublayer which contains an
Express MAC and a Preemptible MAC. Both MACs are hidden to higher and
lower layers and visible as a single MAC (packet classification to eMAC
or pMAC on TX is done based on priority; classification on RX is done
based on SFD).
For devices which support a MAC Merge sublayer, it is desirable to
retrieve individual packet counters from the eMAC and the pMAC, as well
as aggregate statistics (their sum).
Introduce a new ETHTOOL_A_STATS_SRC attribute which is part of the
policy of ETHTOOL_MSG_STATS_GET and, and an ETHTOOL_A_PAUSE_STATS_SRC
which is part of the policy of ETHTOOL_MSG_PAUSE_GET (accepted when
ETHTOOL_FLAG_STATS is set in the common ethtool header). Both of these
take values from enum ethtool_mac_stats_src, defaulting to "aggregate"
in the absence of the attribute.
Existing drivers do not need to pay attention to this enum which was
added to all driver-facing structures, just the ones which report the
MAC merge layer as supported.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC merge sublayer (IEEE 802.3-2018 clause 99) is one of 2
specifications (the other being Frame Preemption; IEEE 802.1Q-2018
clause 6.7.2), which work together to minimize latency caused by frame
interference at TX. The overall goal of TSN is for normal traffic and
traffic with a bounded deadline to be able to cohabitate on the same L2
network and not bother each other too much.
The standards achieve this (partly) by introducing the concept of
preemptible traffic, i.e. Ethernet frames that have a custom value for
the Start-of-Frame-Delimiter (SFD), and these frames can be fragmented
and reassembled at L2 on a link-local basis. The non-preemptible frames
are called express traffic, they are transmitted using a normal SFD, and
they can preempt preemptible frames, therefore having lower latency,
which can matter at lower (100 Mbps) link speeds, or at high MTUs (jumbo
frames around 9K). Preemption is not recursive, i.e. a P frame cannot
preempt another P frame. Preemption also does not depend upon priority,
or otherwise said, an E frame with prio 0 will still preempt a P frame
with prio 7.
In terms of implementation, the standards talk about the presence of an
express MAC (eMAC) which handles express traffic, and a preemptible MAC
(pMAC) which handles preemptible traffic, and these MACs are multiplexed
on the same MII by a MAC merge layer.
To support frame preemption, the definition of the SFD was generalized
to SMD (Start-of-mPacket-Delimiter), where an mPacket is essentially an
Ethernet frame fragment, or a complete frame. Stations unaware of an SMD
value different from the standard SFD will treat P frames as error
frames. To prevent that from happening, a negotiation process is
defined.
On RX, packets are dispatched to the eMAC or pMAC after being filtered
by their SMD. On TX, the eMAC/pMAC classification decision is taken by
the 802.1Q spec, based on packet priority (each of the 8 user priority
values may have an admin-status of preemptible or express).
The MAC Merge layer and the Frame Preemption parameters have some degree
of independence in terms of how software stacks are supposed to deal
with them. The activation of the MM layer is supposed to be controlled
by an LLDP daemon (after it has been communicated that the link partner
also supports it), after which a (hardware-based or not) verification
handshake takes place, before actually enabling the feature. So the
process is intended to be relatively plug-and-play. Whereas FP settings
are supposed to be coordinated across a network using something
approximating NETCONF.
The support contained here is exclusively for the 802.3 (MAC Merge)
portions and not for the 802.1Q (Frame Preemption) parts. This API is
sufficient for an LLDP daemon to do its job. The FP adminStatus variable
from 802.1Q is outside the scope of an LLDP daemon.
I have taken a few creative licenses and augmented the Linux kernel UAPI
compared to the standard managed objects recommended by IEEE 802.3.
These are:
- ETHTOOL_A_MM_PMAC_ENABLED: According to Figure 99-6: Receive
Processing state diagram, a MAC Merge layer is always supposed to be
able to receive P frames. However, this implies keeping the pMAC
powered on, which will consume needless power in applications where FP
will never be used. If LLDP is used, the reception of an Additional
Ethernet Capabilities TLV from the link partner is sufficient
indication that the pMAC should be enabled. So my proposal is that in
Linux, we keep the pMAC turned off by default and that user space
turns it on when needed.
- ETHTOOL_A_MM_VERIFY_ENABLED: The IEEE managed object is called
aMACMergeVerifyDisableTx. I opted for consistency (positive logic) in
the boolean netlink attributes offered, so this is also positive here.
Other than the meaning being reversed, they correspond to the same
thing.
- ETHTOOL_A_MM_MAX_VERIFY_TIME: I found it most reasonable for a LLDP
daemon to maximize the verifyTime variable (delay between SMD-V
transmissions), to maximize its chances that the LP replies. IEEE says
that the verifyTime can range between 1 and 128 ms, but the NXP ENETC
stupidly keeps this variable in a 7 bit register, so the maximum
supported value is 127 ms. I could have chosen to hardcode this in the
LLDP daemon to a lower value, but why not let the kernel expose its
supported range directly.
- ETHTOOL_A_MM_TX_MIN_FRAG_SIZE: the standard managed object is called
aMACMergeAddFragSize, and expresses the "additional" fragment size
(on top of ETH_ZLEN), whereas this expresses the absolute value of the
fragment size.
- ETHTOOL_A_MM_RX_MIN_FRAG_SIZE: there doesn't appear to exist a managed
object mandated by the standard, but user space clearly needs to know
what is the minimum supported fragment size of our local receiver,
since LLDP must advertise a value no lower than that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Cong, introduce a tracepoint for all ->sk_data_ready()
callback implementations. For example:
<...>
iperf-609 [002] ..... 70.660425: sk_data_ready: family=2 protocol=6 func=sock_def_readable
iperf-609 [002] ..... 70.660436: sk_data_ready: family=2 protocol=6 func=sock_def_readable
<...>
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1588 driver loses about 1us in adjtime operation at PTP slave
This is because adjtime operation uses a slow non-atomic tmr_cnt_read()
followed by tmr_cnt_write() operation.
In the above sequence, since the timer counter operation keeps
incrementing, it leads to latency. The tmr_offset register
(which is added to TMR_CNT_H/L register giving the current time)
must be programmed with the delta nanoseconds.
Signed-off-by: Nikhil Gupta <nikhil.gupta@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230119204034.7969-1-nikhil.gupta@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old way of performing a C45 bus transfer created a special
register value and passed it to the MDIO bus driver, in the hope it
would see the MII_ADDR_C45 bit set, and perform a C45 transfer. Now
that there is a clear separation of C22 and C45, this scheme is no
longer used. Remove all the #defines and helpers, to prevent any code
being added which tries to use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, bluetooth, bpf and netfilter.
Current release - regressions:
- Revert "net: team: use IFF_NO_ADDRCONF flag to prevent ipv6
addrconf", fix nsna_ping mode of team
- wifi: mt76: fix bugs in Rx queue handling and DMA mapping
- eth: mlx5:
- add missing mutex_unlock in error reporter
- protect global IPsec ASO with a lock
Current release - new code bugs:
- rxrpc: fix wrong error return in rxrpc_connect_call()
Previous releases - regressions:
- bluetooth: hci_sync: fix use of HCI_OP_LE_READ_BUFFER_SIZE_V2
- wifi:
- mac80211: fix crashes on Rx due to incorrect initialization of
rx->link and rx->link_sta
- mac80211: fix bugs in iTXQ conversion - Tx stalls, incorrect
aggregation handling, crashes
- brcmfmac: fix regression for Broadcom PCIe wifi devices
- rndis_wlan: prevent buffer overflow in rndis_query_oid
- netfilter: conntrack: handle tcp challenge acks during connection
reuse
- sched: avoid grafting on htb_destroy_class_offload when destroying
- virtio-net: correctly enable callback during start_xmit, fix stalls
- tcp: avoid the lookup process failing to get sk in ehash table
- ipa: disable ipa interrupt during suspend
- eth: stmmac: enable all safety features by default
Previous releases - always broken:
- bpf:
- fix pointer-leak due to insufficient speculative store bypass
mitigation (Spectre v4)
- skip task with pid=1 in send_signal_common() to avoid a splat
- fix BPF program ID information in BPF_AUDIT_UNLOAD as well as
PERF_BPF_EVENT_PROG_UNLOAD events
- fix potential deadlock in htab_lock_bucket from same bucket
index but different map_locked index
- bluetooth:
- fix a buffer overflow in mgmt_mesh_add()
- hci_qca: fix driver shutdown on closed serdev
- ISO: fix possible circular locking dependency
- CIS: hci_event: fix invalid wait context
- wifi: brcmfmac: fixes for survey dump handling
- mptcp: explicitly specify sock family at subflow creation time
- netfilter: nft_payload: incorrect arithmetics when fetching VLAN
header bits
- tcp: fix rate_app_limited to default to 1
- l2tp: close all race conditions in l2tp_tunnel_register()
- eth: mlx5: fixes for QoS config and eswitch configuration
- eth: enetc: avoid deadlock in enetc_tx_onestep_tstamp()
- eth: stmmac: fix invalid call to mdiobus_get_phy()
Misc:
- ethtool: add netlink attr in rss get reply only if the value is not
empty"
* tag 'net-6.2-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (88 commits)
Revert "Merge branch 'octeontx2-af-CPT'"
tcp: fix rate_app_limited to default to 1
bnxt: Do not read past the end of test names
net: stmmac: enable all safety features by default
octeontx2-af: add mbox to return CPT_AF_FLT_INT info
octeontx2-af: update cpt lf alloc mailbox
octeontx2-af: restore rxc conf after teardown sequence
octeontx2-af: optimize cpt pf identification
octeontx2-af: modify FLR sequence for CPT
octeontx2-af: add mbox for CPT LF reset
octeontx2-af: recover CPT engine when it gets fault
net: dsa: microchip: ksz9477: port map correction in ALU table entry register
selftests/net: toeplitz: fix race on tpacket_v3 block close
net/ulp: use consistent error code when blocking ULP
octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
tcp: avoid the lookup process failing to get sk in ehash table
Revert "net: team: use IFF_NO_ADDRCONF flag to prevent ipv6 addrconf"
MAINTAINERS: add networking entries for Willem
net: sched: gred: prevent races when adding offloads to stats
l2tp: prevent lockdep issue in l2tp_tunnel_register()
...
When the ACPI part of a driver is optional the methods used in it
are expected to be available even if CONFIG_ACPI=n. This is not
the case for _DSM related methods. Add stubs for
acpi_evaluate_dsm_typed() and acpi_check_dsm() methods.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new helper functions to retrieve a mapping of priority to PCP
and DSCP bitmasks, where each bitmap contains ones in positions that
match a rewrite entry.
dcb_ieee_getrewr_prio_dscp_mask_map() reuses the dcb_ieee_app_prio_map,
as this struct is already used for a similar mapping in the app table.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new rewrite table and all the required functions, offload hooks and
bookkeeping for maintaining it. The rewrite table reuses the app struct,
and the entire set of app selectors. As such, some bookeeping code can
be shared between the rewrite- and the APP table.
New functions for getting, setting and deleting entries has been added.
Apart from operating on the rewrite list, these functions do not emit a
DCB_APP_EVENT when the list os modified. The new dcb_getrewr does a
lookup based on selector and priority and returns the protocol, so that
mappings from priority to protocol, for a given selector and ifindex is
obtained.
Also, a new nested attribute has been added, that encapsulates one or
more app structs. This attribute is used to distinguish the two tables.
The dcb_lock used for the APP table is reused for the rewrite table.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2023-01-18
1) From Rahul,
1.1) extended range for PTP adjtime and adjphase
1.2) adjphase function to support hardware-only offset control
2) From Roi, code cleanup to the TC module.
3) From Maor, TC support for Geneve and GRE with VF tunnel offload
4) Cleanups and minor updates.
* tag 'mlx5-updates-2023-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Use read lock for eswitch get callbacks
net/mlx5e: Remove redundant allocation of spec in create indirect fwd group
net/mlx5e: Support Geneve and GRE with VF tunnel offload
net/mlx5: E-Switch, Fix typo for egress
net/mlx5e: Warn when destroying mod hdr hash table that is not empty
net/mlx5e: TC, Use common function allocating flow mod hdr or encap mod hdr
net/mlx5e: TC, Add tc prefix to attach/detach hdr functions
net/mlx5e: TC, Pass flow attr to attach/detach mod hdr functions
net/mlx5e: Add warning when log WQE size is smaller than log stride size
net/mlx5e: Fail with messages when params are not valid for XSK
net/mlx5: E-switch, Remove redundant comment about meta rules
net/mlx5: Add hardware extended range support for PTP adjtime and adjphase
net/mlx5: Add adjphase function to support hardware-only offset control
net/mlx5: Suppress error logging on UCTX creation
net/mlx5e: Suppress Send WQEBB room warning for PAGE_SIZE >= 16KB
====================
Link: https://lore.kernel.org/r/20230118183602.124323-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove port-specific health reporter destroy function as it is
currently the same as the instance one so no longer needed. Inline
__devlink_health_reporter_destroy() as it is no longer called from
multiple places.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to other devlink objects, rely on devlink instance lock
and remove object specific reporters_lock.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to other devlink objects, protect the reporters list
by devlink instance lock. Alongside add unlocked versions
of health reporter create/destroy functions and use them in drivers
on call paths where the instance lock is held.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MLX5E_LOCKED_FLOW flag is not checked anywhere now so remove it
entirely.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to other devlink objects, convert the linecards list to be
protected by devlink instance lock. Alongside with that rename the
create/destroy() functions to devl_* to indicate the devlink instance
lock needs to be held while calling them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After scanning the bus for C22 devices, check if any Micrel PHYs have
been found. They are known to do bad things if there are C45
transactions on the bus. Prevent the scanning of the bus using C45 if
such a PHY has been detected.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some C22 PHYs do bad things when there are C45 transactions on the
bus. In order to handle this, the bus needs to be scanned first for
C22 at all addresses, and then C45 scanned for all addresses.
The Marvell pxa168 driver scans a specific address on the bus to find
its PHY. This is a C22 only device, so update it to use the c22
helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Somehow an extra 'e' slipped in there without anyone noticing,
drop that from ieeee80211_obss_color_collision_notify().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Neither FIELD_PREP() nor *_encode_bits() can be used
in constant contexts (such as initializers), but we
don't want to define shift constants for all masks
just for use in initializers, and having checks that
the values fit is also useful.
Therefore, add FIELD_PREP_CONST() which is a smaller
version of FIELD_PREP() that can only take constant
arguments and has less friendly (but not less strict)
error checks, and expands to a constant value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230118142652.53f20593504b.Iaeea0aee77a6493d70e573b4aa55c91c00e01e4b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Looks like this is required, even if all of the members
are separately described. Add a line to avoid the warning.
Fixes: f66c48af7a ("mac80211: support minimal EHT rate reporting on RX")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capable hardware can use an extended range for offsetting the clock. An
extended range of [-200000,200000] is used instead of [-32768,32767] for
the delta/phase parameter of the adjtime/adjphase ptp_clock_info callbacks.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add minimal support for RX EHT rate reporting, not yet
adding (modifying) any radiotap headers, just statistics
for cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit b8676221f0 ("cfg80211: Add support for
static WEP in the driver") since no driver ever ended up using
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce NFT_MSG_DESTROY* message type. The destroy operation performs a
delete operation but ignoring the ENOENT errors.
This is useful for the transaction semantics, where failing to delete an
object which does not exist results in aborting the transaction.
This new command allows the transaction to proceed in case the object
does not exist.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
nft_ct expression cannot be made builtin to nf_tables without also
forcing the conntrack itself to be builtin.
However, this can be avoided by splitting retrieval of a few
selector keys that only need to access the nf_conn structure,
i.e. no function calls to nf_conntrack code.
Many rulesets start with something like
"ct status established,related accept"
With this change, this no longer requires an indirect call, which
gives about 1.8% more throughput with a simple conntrack-enabled
forwarding test (retpoline thunk used).
Signed-off-by: Florian Westphal <fw@strlen.de>
