Currently in case the goal length is a multiple of stripe size we use
ext4_mb_scan_aligned() to find the stripe size aligned physical blocks.
In case we are not able to find any, we again go back to calling
ext4_mb_choose_next_group() to search for a different suitable block
group. However, since the linear search always begins from the start,
most of the times we end up with the same BG and the cycle continues.
With large fliesystems, the CPU can be stuck in this loop for hours
which can slow down the whole system. Hence, until we figure out a
better way to continue the search (rather than starting from beginning)
in ext4_mb_choose_next_group(), lets just fallback to
ext4_mb_complex_scan_group() in case aligned scan fails, as it is much
more likely to find the needed blocks.
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/ee033f6dfa0a7f2934437008a909c3788233950f.1702455010.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The ext4 filesystem tracks the trim status of blocks at the group
level. When an entire group has been trimmed then it is marked as
such and subsequent trim invocations with the same minimum trim size
will not be attempted on that group unless it is marked as able to be
trimmed again such as when a block is freed.
Currently the last group can't be marked as trimmed due to incorrect
logic in ext4_last_grp_cluster(). ext4_last_grp_cluster() is supposed
to return the zero based index of the last cluster in a group. This is
then used by ext4_try_to_trim_range() to determine if the trim
operation spans the entire group and as such if the trim status of the
group should be recorded.
ext4_last_grp_cluster() takes a 0 based group index, thus the valid
values for grp are 0..(ext4_get_groups_count - 1). Any group index
less than (ext4_get_groups_count - 1) is not the last group and must
have EXT4_CLUSTERS_PER_GROUP(sb) clusters. For the last group we need
to calculate the number of clusters based on the number of blocks in
the group. Finally subtract 1 from the number of clusters as zero
based indexing is expected. Rearrange the function slightly to make
it clear what we are calculating and returning.
Reproducer:
// Create file system where the last group has fewer blocks than
// blocks per group
$ mkfs.ext4 -b 4096 -g 8192 /dev/nvme0n1 8191
$ mount /dev/nvme0n1 /mnt
Before Patch:
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group not marked as trimmed so second invocation still discards blocks
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
After Patch:
fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group marked as trimmed so second invocation DOESN'T discard any blocks
fstrim -v /mnt
/mnt: 0 B (0 bytes) trimmed
Fixes: 45e4ab320c ("ext4: move setting of trimmed bit into ext4_try_to_trim_range()")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231213051635.37731-1-surajjs@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull pstore updates from Kees Cook:
- Do not allow misconfigured ECC sizes (Sergey Shtylyov)
- Allow for odd number of CPUs (Weichen Chen)
- Refactor error handling to use cleanup.h
* tag 'pstore-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: inode: Use cleanup.h for struct pstore_private
pstore: inode: Use __free(pstore_iput) for inode allocations
pstore: inode: Convert mutex usage to guard(mutex)
pstore: inode: Convert kfree() usage to __free(kfree)
pstore: ram_core: fix possible overflow in persistent_ram_init_ecc()
pstore/ram: Fix crash when setting number of cpus to an odd number
Pull overlayfs updates from Amir Goldstein:
"This is a very small update with no bug fixes and no new features.
The larger update of overlayfs for this cycle, the re-factoring of
overlayfs code into generic backing_file helpers, was already merged
via Christian.
Summary:
- Simplify/clarify some code
No bug fixes here, just some changes following questions from Al
about overlayfs code that could be a little more simple to follow.
- Overlayfs documentation style fixes
Mainly fixes for ReST formatting suggested by documentation
developers"
* tag 'ovl-update-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
overlayfs.rst: fix ReST formatting
overlayfs.rst: use consistent feature names
ovl: initialize ovl_copy_up_ctx.destname inside ovl_do_copy_up()
ovl: remove redundant ofs->indexdir member
This originally came from the aio side, and it's laid out rather oddly.
The common case here is that we either get -EIOCBQUEUED from submitting
an async request, or that we complete the request correctly with the
given number of bytes. Handling the odd internal restart error codes
is not a common operation.
Lay it out a bit more optimally that better explains the normal flow,
and switch to avoiding the indirect call completely as this is our
kiocb and we know the completion handler can only be one of two
possible variants. While at it, move it to where it belongs in the
file, with fellow end IO helpers.
Outside of being easier to read, this also reduces the text size of the
function by 24 bytes for me on arm64.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull erofs updates from Gao Xiang:
"In this cycle, we'd like to enable basic sub-page compressed data
support for Android ecosystem (for vendors to try out 16k page size
with 4k-block images in their compatibility mode) as well as container
images (so that 4k-block images can be parsed on arm64 cloud servers
using 64k page size.)
In addition, there are several bugfixes and cleanups as usual. All
commits have been in -next for a while and no potential merge conflict
is observed.
Summary:
- Add basic sub-page compressed data support
- Fix a memory leak on MicroLZMA and DEFLATE compression
- Fix a rare LZ4 inplace decompression issue on recent x86 CPUs
- Fix a KASAN issue reported by syzbot around crafted images
- Some cleanups"
* tag 'erofs-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: make erofs_{err,info}() support NULL sb parameter
erofs: avoid debugging output for (de)compressed data
erofs: allow partially filled compressed bvecs
erofs: enable sub-page compressed block support
erofs: refine z_erofs_transform_plain() for sub-page block support
erofs: fix ztailpacking for subpage compressed blocks
erofs: fix up compacted indexes for block size < 4096
erofs: record `pclustersize` in bytes instead of pages
erofs: support I/O submission for sub-page compressed blocks
erofs: fix lz4 inplace decompression
erofs: fix memory leak on short-lived bounced pages
During resets, if queues are unquiesced first, then the host can submit
IOs to the controller using shadow doorbell logic but the controller
won't be aware. This can lead to necessary MMIO doorbells from being
not issued, causing requests to be delayed and timed-out.
Signed-off-by: William Butler <wab@google.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Pull fscrypt updates from Eric Biggers:
"Adjust the timing of the fscrypt keyring destruction, to prepare for
btrfs's fscrypt support.
Also document that CephFS supports fscrypt now"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fs: move fscrypt keyring destruction to after ->put_super
f2fs: move release of block devices to after kill_block_super()
fscrypt: document that CephFS supports fscrypt now
fscrypt: update comment for do_remove_key()
fscrypt.rst: update definition of struct fscrypt_context_v2
Pull nfsd updates from Chuck Lever:
"The bulk of the patches for this release are clean-ups and minor bug
fixes.
There is one significant revert to mention: support for RDMA Read
operations in the server's RPC-over-RDMA transport implementation has
been fixed so it waits for Read completion in a way that avoids tying
up an nfsd thread. This prevents a possible DoS vector if an
RPC-over-RDMA client should become unresponsive during RDMA Read
operations.
As always I am grateful to NFSD contributors, reviewers, and testers"
* tag 'nfsd-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (56 commits)
nfsd: rename nfsd_last_thread() to nfsd_destroy_serv()
SUNRPC: discard sv_refcnt, and svc_get/svc_put
svc: don't hold reference for poolstats, only mutex.
SUNRPC: remove printk when back channel request not found
svcrdma: Implement multi-stage Read completion again
svcrdma: Copy construction of svc_rqst::rq_arg to rdma_read_complete()
svcrdma: Add back svcxprt_rdma::sc_read_complete_q
svcrdma: Add back svc_rdma_recv_ctxt::rc_pages
svcrdma: Clean up comment in svc_rdma_accept()
svcrdma: Remove queue-shortening warnings
svcrdma: Remove pointer addresses shown in dprintk()
svcrdma: Optimize svc_rdma_cc_init()
svcrdma: De-duplicate completion ID initialization helpers
svcrdma: Move the svc_rdma_cc_init() call
svcrdma: Remove struct svc_rdma_read_info
svcrdma: Update the synopsis of svc_rdma_read_special()
svcrdma: Update the synopsis of svc_rdma_read_call_chunk()
svcrdma: Update synopsis of svc_rdma_read_multiple_chunks()
svcrdma: Update synopsis of svc_rdma_copy_inline_range()
svcrdma: Update the synopsis of svc_rdma_read_data_item()
...
Pull dlm updates from David Teigland:
"This set cleans up the interface between nfs lockd and dlm, which is
handling nfs file locking for gfs2 and ocfs2. Very basic lockd
functionality is fixed, in which the fl owner was using the lockd pid
instead of the owner value from nfs"
* tag 'dlm-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: update format header reflect current format
dlm: fix format seq ops type 4
dlm: implement EXPORT_OP_ASYNC_LOCK
dlm: use FL_SLEEP to determine blocking vs non-blocking
dlm: use fl_owner from lockd
dlm: use kernel_connect() and kernel_bind()
Pull afs updates from David Howells:
"The majority of the patches are aimed at fixing and improving the AFS
filesystem's rotation over server IP addresses, but there are also
some fixes from Oleg Nesterov for the use of read_seqbegin_or_lock().
- Fix fileserver probe handling so that the next round of probes
doesn't break ongoing server/address rotation by clearing all the
probe result tracking. This could occasionally cause the rotation
algorithm to drop straight through, give a 'successful' result
without actually emitting any RPC calls, leaving the reply buffer
in an undefined state.
Instead, detach the probe results into a separate struct and
allocate a new one each time we start probing and update the
pointer to it. Probes are also sent in order of address preference
to try and improve the chance that the preferred one will complete
first.
- Fix server rotation so that it uses configurable address
preferences across on the probes that have completed so far than
ranking them by RTT as the latter doesn't necessarily give the best
route. The preference list can be altered by writing into
/proc/net/afs/addr_prefs.
- Fix the handling of Read-Only (and Backup) volume callbacks as
there is one per volume, not one per file, so if someone performs a
command that, say, offlines the volume but doesn't change it, when
it comes back online we don't spam the server with a status fetch
for every vnode we're using. Instead, check the Creation timestamp
in the VolSync record when prompted by a callback break.
- Handle volume regression (ie. a RW volume being restored from a
backup) by scrubbing all cache data for that volume. This is
detected from the VolSync creation timestamp.
- Adjust abort handling and abort -> error mapping to match better
with what other AFS clients do.
- Fix offline and busy volume state handling as they only apply to
individual server instances and not entire volumes and the rotation
algorithm should go and look at other servers if available. Also
make it sleep briefly before each retry if all the volume instances
are unavailable"
* tag 'afs-fix-rotation-20240105' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (40 commits)
afs: trace: Log afs_make_call(), including server address
afs: Fix offline and busy message emission
afs: Fix fileserver rotation
afs: Overhaul invalidation handling to better support RO volumes
afs: Parse the VolSync record in the reply of a number of RPC ops
afs: Don't leave DONTUSE/NEWREPSITE servers out of server list
afs: Fix comment in afs_do_lookup()
afs: Apply server breaks to mmap'd files in the call processor
afs: Move the vnode/volume validity checking code into its own file
afs: Defer volume record destruction to a workqueue
afs: Make it possible to find the volumes that are using a server
afs: Combine the endpoint state bools into a bitmask
afs: Keep a record of the current fileserver endpoint state
afs: Dispatch vlserver probes in priority order
afs: Dispatch fileserver probes in priority order
afs: Mark address lists with configured priorities
afs: Provide a way to configure address priorities
afs: Remove the unimplemented afs_cmp_addr_list()
afs: Add some more info to /proc/net/afs/servers
rxrpc: Create a procfile to display outstanding client conn bundles
...
Pull jfs updates from David Kleikamp:
"Stability improvements"
* tag 'jfs-6.8' of github.com:kleikamp/linux-shaggy:
jfs: Add missing set_freezable() for freezable kthread
jfs: fix array-index-out-of-bounds in diNewExt
jfs: fix shift-out-of-bounds in dbJoin
jfs: fix uaf in jfs_evict_inode
jfs: fix array-index-out-of-bounds in dbAdjTree
jfs: fix slab-out-of-bounds Read in dtSearch
UBSAN: array-index-out-of-bounds in dtSplitRoot
FS:JFS:UBSAN:array-index-out-of-bounds in dbAdjTree
Deleting the old mr during mr update (.set_map) and then modifying the
vqs with the new mr is not a good flow for firmware. The firmware
expects that mkeys are deleted after there are no more vqs referencing
them.
Introduce reference counting for mrs to fix this. It is the only way to
make sure that mkeys are not in use by vqs.
An mr reference is taken when the mr is associated to the mr asid table
and when the mr is linked to the vq on create/modify. The reference is
released when the mkey is unlinked from the vq (trough modify/destroy)
and from the mr asid table.
To make things consistent, get rid of mlx5_vdpa_destroy_mr and use
get/put semantics everywhere.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20231225151203.152687-8-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of tearing down and setting up vq resources, use vq
suspend/resume during .set_map to speed things up a bit.
The vq mr is updated with the new mapping while the vqs are suspended.
If the device doesn't support resumable vqs, do the old teardown and
setup dance.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20231225151203.152687-7-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.set_vq_state will set the indices and mark the fields to be modified in
the hw vq.
Advertise that the device supports changing the vq state when the device
is in DRIVER_OK state and suspended.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231225151203.152687-6-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio standard doesn't allow for virtqueue address and state
changes when the device is in DRIVER_OK. Return an error in such cases
unless the device is suspended.
The suspended device exception is needed because some devices support
virtqueue changes when the device is suspended.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Suggested-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20231225134210.151540-3-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set vdpa device suspended state on successful suspend. Clear it on
successful resume and reset.
The state will be locked by the vhost_vdpa mutex. The mutex is taken
during suspend, resume and reset in vhost_vdpa_unlocked_ioctl. The
exception is vhost_vdpa_open which does a device reset but that should
be safe because it can only happen before the other ops.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Suggested-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20231225134210.151540-2-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds polling support to virtio-scsi. It's based on and works similar
to virtblk support where we add a module param to specify the number of
poll queues then subtract to calculate the IO queues.
When using 8 poll queues and a vhost worker per queue we see 4K IOPs
with fio:
fio --filename=/dev/sda --direct=1 --rw=randread --bs=4k \
--ioengine=io_uring --hipri --iodepth=128 --numjobs=$NUM_JOBS
increase like:
jobs base poll
1 207K 296K
2 392K 552K
3 581K 860K
4 765K 1235K
5 936K 1598K
6 1104K 1880K
7 1253K 2095K
8 1311k 2187K
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20231214052649.57743-1-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds the support for feature VIRTIO_PMEM_F_SHMEM_REGION
(virtio spec v1.2 section 5.19.5.2 [1]).
During feature negotiation, if VIRTIO_PMEM_F_SHMEM_REGION is offered
by the device, the driver looks for a shared memory region of id 0.
If it is found, this feature is understood. Otherwise, this feature
bit is cleared.
During probe, if VIRTIO_PMEM_F_SHMEM_REGION has been negotiated,
virtio pmem ignores the `start` and `size` fields in device config
and uses the physical address range of shared memory region 0.
[1] https://docs.oasis-open.org/virtio/virtio/v1.2/csd01/virtio-v1.2-csd01.html#x1-6480002
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Message-Id: <20231220204906.566922-1-changyuanl@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
A virtio_balloon's parent device may be configured so that a
configuration change interrupt is a wakeup event. Extend the processing
of such a wakeup event until the balloon finishes inflating or deflating
by calling pm_stay_awake/pm_relax in the virtio_balloon driver. Note
that these calls are no-ops if the parent device doesn't support wakeup
events or if the wakeup events are not enabled.
This change allows the guest to use system power states such as s2idle
without running the risk the virtio_balloon's cooperative memory
management becoming unresponsive to the host's requests.
Tested-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: David Stevens <stevensd@chromium.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Message-Id: <20240110021925.1137333-1-stevensd@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously, we use alternative mechanism to dynamically patch
the CMO operations for THEAD C906/C910 during boot for performance
reason. But as pointed out by Arnd, "there is already a significant
cost in accessing the invalidated cache lines afterwards, which is
likely going to be much higher than the cost of an indirect branch".
And indeed, there's no performance difference with GMAC and EMMC per
my test on Sipeed Lichee Pi 4A board.
Use riscv_nonstd_cache_ops for THEAD C906/C910 CMO to simplify
the alternative code, and to acchieve Arnd's goal -- "I think
moving the THEAD ops at the same level as all nonstandard operations
makes sense, but I'd still leave CMO as an explicit fast path that
avoids the indirect branch. This seems like the right thing to do both
for readability and for platforms on which the indirect branch has a
noticeable overhead."
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231114143338.2406-2-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Pull gfs2 updates from Andreas Gruenbacher:
- Add support for non-blocking lookup (MAY_NOT_BLOCK / LOOKUP_RCU)
- Various minor fixes and cleanups
* tag 'gfs2-v6.7-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix freeze consistency check in log_write_header
gfs2: Refcounting fix in gfs2_thaw_super
gfs2: Minor gfs2_{freeze,thaw}_super cleanup
gfs2: Use wait_event_freezable_timeout() for freezable kthread
gfs2: Add missing set_freezable() for freezable kthread
gfs2: Remove use of error flag in journal reads
gfs2: Lift withdraw check out of gfs2_ail1_empty
gfs2: Rename gfs2_withdrawn to gfs2_withdrawing_or_withdrawn
gfs2: Mark withdraws as unlikely
gfs2: Minor gfs2_ail1_empty cleanup
gfs2: use is_subdir()
gfs2: d_obtain_alias(ERR_PTR(...)) will do the right thing
gfs2: Use GL_NOBLOCK flag for non-blocking lookups
gfs2: Add GL_NOBLOCK flag
gfs2: rgrp: fix kernel-doc warnings
gfs2: fix kernel BUG in gfs2_quota_cleanup
gfs2: Fix inode_go_instantiate description
gfs2: Fix kernel NULL pointer dereference in gfs2_rgrp_dump
Pull btrfs updates from David Sterba:
"There are no exciting changes for users, it's been mostly API
conversions and some fixes or refactoring.
The mount API conversion is a base for future improvements that would
come with VFS. Metadata processing has been converted to folios, not
yet enabling the large folios but it's one patch away once everything
gets tested enough.
Core changes:
- convert extent buffers to folios:
- direct API conversion where possible
- performance can drop by a few percent on metadata heavy
workloads, the folio sizes are not constant and the calculations
add up in the item helpers
- both regular and subpage modes
- data cannot be converted yet, we need to port that to iomap and
there are some other generic changes required
- convert mount to the new API, should not be user visible:
- options deprecated long time ago have been removed: inode_cache,
recovery
- the new logic that splits mount to two phases slightly changes
timing of device scanning for multi-device filesystems
- LSM options will now work (like for selinux)
- convert delayed nodes radix tree to xarray, preserving the
preload-like logic that still allows to allocate with GFP_NOFS
- more validation of sysfs value of scrub_speed_max
- refactor chunk map structure, reduce size and improve performance
- extent map refactoring, smaller data structures, improved
performance
- reduce size of struct extent_io_tree, embedded in several
structures
- temporary pages used for compression are cached and attached to a
shrinker, this may slightly improve performance
- in zoned mode, remove redirty extent buffer tracking, zeros are
written in case an out-of-order is detected and proper data are
written to the actual write pointer
- cleanups, refactoring, error message improvements, updated tests
- verify and update branch name or tag
- remove unwanted text"
* tag 'for-6.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (89 commits)
btrfs: pass btrfs_io_geometry into btrfs_max_io_len
btrfs: pass struct btrfs_io_geometry to set_io_stripe
btrfs: open code set_io_stripe for RAID56
btrfs: change block mapping to switch/case in btrfs_map_block
btrfs: factor out block mapping for single profiles
btrfs: factor out block mapping for RAID5/6
btrfs: reduce scope of data_stripes in btrfs_map_block
btrfs: factor out block mapping for RAID10
btrfs: factor out block mapping for DUP profiles
btrfs: factor out RAID1 block mapping
btrfs: factor out block-mapping for RAID0
btrfs: re-introduce struct btrfs_io_geometry
btrfs: factor out helper for single device IO check
btrfs: migrate btrfs_repair_io_failure() to folio interfaces
btrfs: migrate eb_bitmap_offset() to folio interfaces
btrfs: migrate various end io functions to folios
btrfs: migrate subpage code to folio interfaces
btrfs: migrate get_eb_page_index() and get_eb_offset_in_page() to folios
btrfs: don't double put our subpage reference in alloc_extent_buffer
btrfs: cleanup metadata page pointer usage
...
Pull xfs updates from Chandan Babu:
"New features/functionality:
- Online repair:
- Reserve disk space for online repairs
- Fix misinteraction between the AIL and btree bulkloader because
of which the bulk load fails to queue a buffer for writeback if
it happens to be on the AIL list
- Prevent transaction reservation overflows when reaping blocks
during online repair
- Whenever possible, bulkloader now copies multiple records into
a block
- Support repairing of
1. Per-AG free space, inode and refcount btrees
2. Ondisk inodes
3. File data and attribute fork mappings
- Verify the contents of
1. Inode and data fork of realtime bitmap file
2. Quota files
- Introduce MF_MEM_PRE_REMOVE. This will be used to notify tasks
about a pmem device being removed
Bug fixes:
- Fix memory leak of recovered attri intent items
- Fix UAF during log intent recovery
- Fix realtime geometry integer overflows
- Prevent scrub from live locking in xchk_iget
- Prevent fs shutdown when removing files during low free disk space
- Prevent transaction reservation overflow when extending an RT
device
- Prevent incorrect warning from being printed when extending a
filesystem
- Fix an off-by-one error in xreap_agextent_binval
- Serialize access to perag radix tree during deletion operation
- Fix perag memory leak during growfs
- Allow allocation of minlen realtime extent when the maximum sized
realtime free extent is minlen in size
Cleanups:
- Remove duplicate boilerplate code spread across functionality
associated with different log items
- Cleanup resblks interfaces
- Pass defer ops pointer to defer helpers instead of an enum
- Initialize di_crc in xfs_log_dinode to prevent KMSAN warnings
- Use static_assert() instead of BUILD_BUG_ON_MSG() to validate size
of structures and structure member offsets. This is done in order
to be able to share the code with userspace
- Move XFS documentation under a new directory specific to XFS
- Do not invoke deferred ops' ->create_done callback if the deferred
operation does not have an intent item associated with it
- Remove duplicate inclusion of header files from scrub/health.c
- Refactor Realtime code
- Cleanup attr code"
* tag 'xfs-6.8-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (123 commits)
xfs: use the op name in trace_xlog_intent_recovery_failed
xfs: fix a use after free in xfs_defer_finish_recovery
xfs: turn the XFS_DA_OP_REPLACE checks in xfs_attr_shortform_addname into asserts
xfs: remove xfs_attr_sf_hdr_t
xfs: remove struct xfs_attr_shortform
xfs: use xfs_attr_sf_findname in xfs_attr_shortform_getvalue
xfs: remove xfs_attr_shortform_lookup
xfs: simplify xfs_attr_sf_findname
xfs: move the xfs_attr_sf_lookup tracepoint
xfs: return if_data from xfs_idata_realloc
xfs: make if_data a void pointer
xfs: fold xfs_rtallocate_extent into xfs_bmap_rtalloc
xfs: simplify and optimize the RT allocation fallback cascade
xfs: reorder the minlen and prod calculations in xfs_bmap_rtalloc
xfs: remove XFS_RTMIN/XFS_RTMAX
xfs: remove rt-wrappers from xfs_format.h
xfs: factor out a xfs_rtalloc_sumlevel helper
xfs: tidy up xfs_rtallocate_extent_exact
xfs: merge the calls to xfs_rtallocate_range in xfs_rtallocate_block
xfs: reflow the tail end of xfs_rtallocate_extent_block
...
Pull fsnotify updates from Jan Kara:
"fanotify changes allowing use of fanotify directory events even for
filesystems such as FUSE which don't report proper fsid"
* tag 'fsnotify_for_v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: allow "weak" fsid when watching a single filesystem
fanotify: store fsid in mark instead of in connector
Pull small quota cleanup from Jan Kara.
* tag 'fs_for_v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: convert dquot_claim_space_nodirty() to return void
Partial completions of zone append request is not allowed but if a zone
append completion indicates a number of completed bytes different from
the original BIO size, only the BIO status is set to error. This leads
to bio_advance() not setting the BIO size to 0 and thus to not call
bio_endio() at the end of req_bio_endio().
Make sure a partially completed zone append is failed and completed
immediately by forcing the completed number of bytes (nbytes) to be
equal to the BIO size, thus ensuring that bio_endio() is called.
Fixes: 297db73184 ("block: fix req_bio_endio append error handling")
Cc: stable@kernel.vger.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240110092942.442334-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If CONFIG_TRACEPOINTS isn't enabled, we assign this variable but then
never use it. This can cause the compiler to complain about that:
block/blk-iocost.c:1264:6: warning: variable 'last_period' set but not used [-Wunused-but-set-variable]
1264 | u64 last_period, cur_period;
| ^
Rather than add ifdefs to guard this, just mark it __maybe_unused.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401102335.GiWdeIo9-lkp@intel.com/
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix two typos in the admin-guide:
- a missing e in "reference_perf" in cppc_sysfs.rst.
- the amd_pstate sysfs path uses a dash instead of an underscore.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some Meteor Lake platforms, maximum one core turbo frequency is not
observed. During hybrid performance to frequency conversion, the maximum
frequency is 100 MHz less. This results in requesting maximum frequency
100 MHz less.
For example when the max one core turbo is 4.9 GHz:
MSR HWP_CAPABILITIES shows highest performance ratio for P-core is 0x3E.
With the current scaling factor of 78741 (1.27x for converting frequency
to performance) results in max frequency of 4.8 GHz. This results in
capping the max scaling frequency as 4.8 GHz, which is 100 MHz less than
the desired.
Add capability to define per CPU model specific scaling factor and define
scaling factor of 80000 (1.25x for converting frequency to performance for
P-cores) for Meteor Lake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Debug message adjustment, subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the extra 'mt8195-afe-pcm-dai' component, register the DAI
drivers to the main AFE component, and rework the DAI linking between
the headset codec (RT5682/RT5682S) and the TDM interface in the probe
function to stop assigning name, relying on the of_node of the codec.
Also replace the COMP_DUMMY codec entry with a COMP_EMPTY for the
ETDM2_IN and remove it entirely from ETDM1_OUT to fix the registration
flow for this sound card.
While at it, since we also need to swap the codec init function from
ETDM2_IN to ETDM1_OUT, remove the static assignment of both `ops` and
`init` for both, as we now assign these dynamically during probe.
Fixes: 13f58267cd ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240110105757.539089-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Syzbot reported a KMSAN warning,
erofs: (device loop0): z_erofs_lz4_decompress_mem: failed to decompress -12 in[46, 4050] out[917]
=====================================================
BUG: KMSAN: uninit-value in hex_dump_to_buffer+0xae9/0x10f0 lib/hexdump.c:194
..
print_hex_dump+0x13d/0x3e0 lib/hexdump.c:276
z_erofs_lz4_decompress_mem fs/erofs/decompressor.c:252 [inline]
z_erofs_lz4_decompress+0x257e/0x2a70 fs/erofs/decompressor.c:311
z_erofs_decompress_pcluster fs/erofs/zdata.c:1290 [inline]
z_erofs_decompress_queue+0x338c/0x6460 fs/erofs/zdata.c:1372
z_erofs_runqueue+0x36cd/0x3830
z_erofs_read_folio+0x435/0x810 fs/erofs/zdata.c:1843
The root cause is that the printed decompressed buffer may be filled
incompletely due to decompression failure. Since they were once only
used for debugging, get rid of them now.
Reported-and-tested-by: syzbot+6c746eea496f34b3161d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/000000000000321c24060d7cfa1c@google.com
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231227151903.2900413-1-hsiangkao@linux.alibaba.com
Use debian/<package> for tmpdir, which is the default of debhelper.
This simplifies the code.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Strictly speaking, 'make headers' should be a part of build-arch
instead of binary-arch.
'make headers' constructs ready-to-copy UAPI headers in the kernel
directory.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
