Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
Pull MTD updates from Miquel Raynal:
"Core MTD changes:
- Use refcount to prevent corruption
- Call external _get and _put in right order
- Fix use-after-free in mtd release
- Explicitly include correct DT includes
- Clean refcounting with MTD_PARTITIONED_MASTER
- mtdblock: make warning messages ratelimited
- dt-bindings: Add SEAMA partition bindings
Device driver changes:
- Use devm helper functions
- Fix questionable cast, remove pointless ones.
- error handling fixes
- add support for new chip versions
- update DT bindings
- misc cleanups - fix typos, whitespace, indentation"
* tag 'mtd/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (105 commits)
dt-bindings: mtd: amlogic,meson-nand: drop unneeded quotes
mtd: spear_smi: Use helper function devm_clk_get_enabled()
mtd: rawnand: orion: Use helper function devm_clk_get_optional_enabled()
mtd: rawnand: vf610_nfc: Use helper function devm_clk_get_enabled()
mtd: rawnand: sunxi: Use helper function devm_clk_get_enabled()
mtd: rawnand: stm32_fmc2: Use helper function devm_clk_get_enabled()
mtd: rawnand: mtk: Use helper function devm_clk_get_enabled()
mtd: rawnand: mpc5121: Use helper function devm_clk_get_enabled()
mtd: rawnand: lpc32xx_slc: Use helper function devm_clk_get_enabled()
mtd: rawnand: intel: Use helper function devm_clk_get_enabled()
mtd: rawnand: fsmc: Use helper function devm_clk_get_enabled()
mtd: rawnand: arasan: Use helper function devm_clk_get_enabled()
mtd: rawnand: qcom: Add read/read_start ops in exec_op path
mtd: rawnand: qcom: Clear buf_count and buf_start in raw read
mtd: maps: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()
mtd: rawnand: qcom: Sort includes alphabetically
mtd: rawnand: qcom: Do not override the error no of submit_descs()
...
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NOR core changes:
* fix assumption on enabling quad mode in
spi_nor_write_16bit_sr_and_check()
* avoid setting SRWD bit in SR if WP# signal not connected as it will
configure the SR permanently as read only. Add "no-wp" dt property.
* clarify the need for spi-nor compatibles in dt-bindings
SPI NOR manufacturer drivers changes:
* spansion:
- add support for S28HS02GT
- switch methods to use vreg_offset from SFDP instead of hardcoding
the register value
* microchip/sst:
- add support for sst26vf032b flash
* winbond:
- correct flags for Winbond w25q128
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Binding files should be dual licensed. This file was initially written
as a .txt file with no specific license, so was implicitely
GPLv2. Significant part of this file and its conversion into yaml were
written by Bootlin employees which agree to comply with the rules
regarding the dual licensing so let's fix the SPDX tag to reflect the
correct license by changing it from GPL to GPL + BSD-2-Clause.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230712151042.433593-1-miquel.raynal@bootlin.com
Most SPI NOR devices do not require a specific compatible, their ID can
in general be discovered with the JEDEC READ ID opcode. In this case,
only the "jedec,spi-nor" generic compatible is expected. Clarify this
information in the compatible description to (i) help device-tree
writers and (ii) prevent further attempts to extend this list with
useless information.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230616140054.2788684-1-miquel.raynal@bootlin.com
[ta: s/JEDEC/JEDEC SFDP for clarity and s/JEDEC READ ID/READ ID as
the opcode is not part of the JEDEC SFDP standard.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
If the WP# signal of the flash device is either not connected or is wrongly
tied to GND (that includes internal pull-downs), and the software sets the
status register write disable (SRWD) bit in the status register then the
status register permanently becomes read-only. To avoid this added a new
boolean DT property "no-wp". If this property is set in the DT then the
software avoids setting the SRWD during status register write operation.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230630142233.63585-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Pull more devicetree updates from Rob Herring:
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT
schema
* tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: soc: qcom: stats: Update maintainer email
dt-bindings: cleanup DTS example whitespaces
dt-bindings: timestamp: restrict node name suffixes
dt-bindings: slimbus: restrict node name suffixes
dt-bindings: watchdog: restrict node name suffixes
dt-bindings: watchdog: brcm,kona-wdt: convert txt file to yaml
dt-bindings: watchdog: cdns,wdt-r1p2: Convert cadence watchdog to yaml
nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-13-miquel.raynal@bootlin.com
nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-9-miquel.raynal@bootlin.com
In an effort to constrain as much as we can the existing binding, we
want to add "unevaluatedProperties: false" in all the NAND chip
descriptions part of NAND controller bindings. But in order to do that
properly, we also need to reference a file which contains all the
"allowed" properties. Right now this file is nand-chip.yaml but in
practice raw NAND controllers may use additional properties in their
NAND chip children node. These properties are listed under
nand-controller.yaml, which makes the "unevaluatedProperties" checks
fail while the description are valid. We need to move these NAND chip
related properties into another file, because we do not want to pollute
nand-chip.yaml which is also referenced by eg. SPI-NAND devices.
Let's create a raw-nand-chip.yaml file to reference all the properties a
raw NAND chip description can contain. The chain of inheritance becomes:
nand-controller.yaml <- raw-nand-chip.yaml
raw-nand-chip.yaml <- nand-chip.yaml
spi-nand.yaml <- nand-chip.yaml
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-3-miquel.raynal@bootlin.com
There is no addition there, but the mtd.yaml file is so generic, it can
be referenced by a wide variety of devices, including nand ones which
already define the node name to "nand@<cs>". Right now it does not lead
to any failure but when we will constrain more the schema, this will
become a problem because we want the mtd-wide properties like label or
partitions to be available for the callers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-2-miquel.raynal@bootlin.com
It's supposed to be there and it's needed for proper validation of DTS
files.
This fixes following errors for Northstar based TP-Link routers:
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions: 'oneOf' conditional failed, one must be fixed:
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: 'pinctrl-[0-9]+'
'#address-cells' is a required property
'#size-cells' is a required property
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: '^partition@[0-9a-f]+$', 'pinctrl-[0-9]+'
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: '^partition-[0-9a-z]+$', 'pinctrl-[0-9]+'
'fis-index-block' is a required property
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions:compatible: 'oneOf' conditional failed, one must be fixed:
['tplink,safeloader-partitions'] is too short
'fixed-partitions' was expected
'sercomm,sc-partitions' was expected
'arm,arm-firmware-suite' was expected
'brcm,bcm4908-partitions' was expected
'brcm,bcm947xx-cfe-partitions' was expected
'linksys,ns-partitions' was expected
'qcom,smem-part' was expected
'redboot-fis' was expected
From schema: Documentation/devicetree/bindings/mtd/mtd.yaml
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions: Unevaluated properties are not allowed ('partitions-table-offset' was unexpected)
From schema: Documentation/devicetree/bindings/mtd/mtd.yaml
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions: 'oneOf' conditional failed, one must be fixed:
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: 'pinctrl-[0-9]+'
'#address-cells' is a required property
'#size-cells' is a required property
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: '^partition@[0-9a-f]+$', 'pinctrl-[0-9]+'
'partition-file-system', 'partition-os-image', 'partitions-table-offset' do not match any of the regexes: '^partition-[0-9a-z]+$', 'pinctrl-[0-9]+'
'fis-index-block' is a required property
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions:compatible: 'oneOf' conditional failed, one must be fixed:
['tplink,safeloader-partitions'] is too short
'fixed-partitions' was expected
'sercomm,sc-partitions' was expected
'arm,arm-firmware-suite' was expected
'brcm,bcm4908-partitions' was expected
'brcm,bcm947xx-cfe-partitions' was expected
'linksys,ns-partitions' was expected
'qcom,smem-part' was expected
'redboot-fis' was expected
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: partitions: Unevaluated properties are not allowed ('partitions-table-offset' was unexpected)
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dtb: flash@0: Unevaluated properties are not allowed ('partitions' was unexpected)
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230602215629.2568-1-zajec5@gmail.com
Pull devicetree fixes from Rob Herring:
- Add Conor Dooley as a DT binding maintainer
- Swap the order of parsing /memreserve/ and /reserved-memory nodes so
that the /reserved-memory nodes which have more information are
handled first
- Fix some property dependencies in riscv,pmu binding
- Update maintainers entries on a couple of bindings
* tag 'devicetree-fixes-for-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
MAINTAINERS: add Conor as a dt-bindings maintainer
dt-bindings: perf: riscv,pmu: fix property dependencies
dt-bindings: xilinx: Remove Naga from memory and mtd bindings
of: fdt: Scan /memreserve/ last
dt-bindings: clock: r9a06g032-sysctrl: Change maintainer to Fabrizio Castro
dt-bindings: pinctrl: renesas,rzv2m: Change maintainer to Fabrizio Castro
dt-bindings: pinctrl: renesas,rzn1: Change maintainer to Fabrizio Castro
dt-bindings: i2c: renesas,rzv2m: Change maintainer to Fabrizio Castro
Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- dt-bindings: Drop unneeded quotes
- mtdblock: Tolerate corrected bit-flips
- Use of_property_read_bool() for boolean properties
- Avoid magic values
- Avoid printing error messages on probe deferrals
- Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
- Fix error path for nvmem provider
- Fix nvmem error reporting
- Provide unique name for nvmem device
MTD device changes:
- lpddr_cmds: Remove unused words variable
- bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
- Introduce Read While Write support for flashes featuring several
banks
- Set the 4-Byte Address Mode method based on SFDP data
- Allow post_sfdp hook to return errors
- Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
- macronix: Add support for mx25uw51245g with RWW
- spansion:
- Determine current address mode at runtime as it can be changed
in a non-volatile way and differ from factory defaults or from
what SFDP advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes:
S25FS256T, s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
- Convert to platform remove callback returning void
- Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
- imx: Remove unused is_imx51_nfc and imx53_nfc functions
- omap2: Drop obsolete dependency on COMPILE_TEST
- orion: Use devm_platform_ioremap_resource()
- qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
- stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
- tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
- hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
- Add support for ESMT F50x1G41LB"
* tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (55 commits)
mtd: nand: Convert to platform remove callback returning void
mtd: onenand: omap2: Drop obsolete dependency on COMPILE_TEST
mtd: spi-nor: spansion: Add support for s25hl02gt and s25hs02gt
mtd: spi-nor: spansion: Add a new ->ready() hook for multi-chip device
mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support
mtd: spi-nor: spansion: Rework cypress_nor_get_page_size() for multi-chip device support
mtd: spi-nor: sfdp: Add support for SCCR map for multi-chip device
mtd: spi-nor: Extract volatile register offset from SCCR map
mtd: spi-nor: Allow post_sfdp hook to return errors
mtd: spi-nor: spansion: Rename method to cypress_nor_get_page_size
mtd: spi-nor: spansion: Enable JFFS2 write buffer for S25FS256T
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s25hx SEMPER flash
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash
mtd: spi-nor: spansion: Determine current address mode
mtd: spi-nor: core: Introduce spi_nor_set_4byte_addr_mode()
mtd: spi-nor: core: Update flash's current address mode when changing address mode
mtd: spi-nor: Stop exporting spi_nor_restore()
mtd: spi-nor: Set the 4-Byte Address Mode method based on SFDP data
mtd: spi-nor: core: Make spi_nor_set_4byte_addr_mode_brwr public
mtd: spi-nor: core: Update name and description of spi_nor_set_4byte_addr_mode
...
Pull MTD updates from Miquel Raynal:
"MTD changes:
- parsers: ofpart: add workaround for #size-cells 0
- dt-bindings: partitions: Fix partition node name pattern
- dataflash: remove duplicate SPI ID table
Raw NAND core changes:
- Check the data only read pattern only once
- Prepare the late addition of supported operation checks
- Support for sequential cache reads
- Fix nand_chip kdoc
Raw NAND driver changes:
- Fsl_elbc: Propagate HW ECC settings to HW
- Marvell: Add missing layouts
- Pasemi: Don't use static data to track per-device state
- Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
- tmio_nand: Remove driver
- vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
- Add support for AllianceMemory AS5F34G04SND
- Macronix: use scratch buffer for DMA operation
NAND ECC changes:
- Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
- Misc core fixes
SPI NOR driver changes:
- Spansion: Minor fixes"
* tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (33 commits)
mtd: parsers: ofpart: add workaround for #size-cells 0
mtd: rawnand: sunxi: Precompute the ECC_CTL register value
mtd: rawnand: sunxi: Embed sunxi_nand_hw_ecc by value
mtd: rawnand: sunxi: Update OOB layout to match hardware
mtd: spi-nor: Sort headers alphabetically
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986
dt-bindings: mtd: Split ECC engine with rawnand controller
mtd: rawnand: fsl_elbc: Propagate HW ECC settings to HW
mtd: spinand: Add support for AllianceMemory AS5F34G04SND
dt-bindings: mtd: partitions: Fix partition node name pattern
mtd: spi-nor: Create macros to define chip IDs and geometries
mtd: spi-nor: spansion: Make CFRx reg fields generic
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: core: fix implicit declaration warning
mtd: spinand: macronix: use scratch buffer for DMA operation
mtd: rawnand: Fix nand_chip kdoc
mtd: rawnand: vf610_nfc: use regular comments for functions
mtd: rawnand: Support for sequential cache reads
...
NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
