The top-level part defines variable number of clocks and interrupts, and
each "if:then:" block narrows them. It however narrows only the
maxItems leaving minItems undefined, which then takes different values
depending on dtschema being used.
Recommended style is to avoid ambiguity in such case, thus if top-level
part has broad constraints, then each "if:then:" must specify both upper
and lower limits.
Add missing constraints, mostly minItems but also maxItems for one
variant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260323-dt-bindings-snps-qcom-dwc3-cleanup-v2-2-3bcd37c0a5b5@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the Cadence USBSS DRD binding to document that it also covers
the USBSSP (SuperSpeed Plus, USB 3.1 gen2x1) controller. Both USBSS
and USBSSP share the same DRD/OTG register interface, so the driver
auto-detects the controller version at runtime — no additional
compatible string is needed.
Changes to the binding:
- Update title and add description
- maximum-speed: add super-speed-plus
This patch is Assisted-by: Cursor:claude-4.6-opus
Signed-off-by: Peter Chen <peter.chen@cixtech.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260316064831.274865-2-peter.chen@cixtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible string for DWC3 USB controller found in SpacemiT K3 SoC.
The USB2.0 host controller in K3 SoC actually use DWC3 IP but only support
USB2.0 functionality, thus in the hardware layer, it has only one USB2 PHY.
While in K1 SoC, the USB controller has both USB2 and USB3 Combo PHY
connected, but able to work in a reduced USB2.0 mode which requres only
one USB2 PHY, leaves the USB3 Combo PHY to PCIe controller. So both K1
and K3 SoC are able to work in the USB2.0 mode which requires one PHY.
Explicitly reduce number of phy property to minimal one.
Signed-off-by: Yixun Lan <dlan@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260320-02-k3-usb20-support-v2-1-308ea0e44038@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Type-C chip know the cable orientation and then normally will set the
switch channel to correctly configure the data path. Some chips itself
support to output the control signal by indicating the capability in
bit[0] of STANDARD_OUTPUT_CAPABILITIES register and do it in
CONFIG_STANDARD_OUTPUT register. For PTN5110 which doesn't present this
capability currently there is no way to achieve the orientation setting.
Add an optional "orientation-gpios" property to achieve the same purpose.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260319-support-setting-orientation-use-gpio-v4-1-ab6dfa8610c2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add additional properties for ports supporting sink mode. The properties
define certain hardware and electrical properties such as sink load
step, sink load characteristics, sink compliance and charging adapter
Power Delivery Profile (PDP) for the connector. These properties need to
be defined for a Type-C port in compliance with the PD 3.1 spec.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260223-skedb-v2-1-60675765bc7e@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb IP on mpfs and pic64gx has a reset pin, but until now this has
been undocumented because platform firmware takes the block out of reset
on first-party boards (or those using modified versions of the vendor
firmware), but not all boards may take this approach. Permit providing a
reset in devicetree for Linux, or other devicetree-consuming software,
to use.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260303-backspace-unhearing-c6cc8cbddbba@spud
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert OMAP MUSB USB OTG Controller binding to DT schema.
Changes during conversion:
- Include "interrupts" and "interrupt-names" properties in the YAML, as
they are used by many in-tree DTS files.
- Extend the "power" property to allow the value 150 (in addition to
existing values), since this is present in several in-tree DTS examples.
- Drop the ti,hwmods property, as it is not used by any in-tree DTS files.
Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260127-ti-usb-v2-1-9dd6a65b43df@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver updates for
7.0-rc1. Overall more lines were removed than added, thanks to
dropping the obsolete isp1362 USB host controller driver, always a
nice change.
Other than that, nothing major happening here, highlights are:
- lots of dwc3 driver updates and new hardware support added
- usb gadget function driver updates
- usb phy driver updates
- typec driver updates and additions
- USB rust binding updates for syntax and formatting changes
- more usb serial device ids added
- other smaller USB core and driver updates and additions
All of these have been in linux-next for a long time, with no reported
problems"
* tag 'usb-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (77 commits)
usb: typec: ucsi: Add Thunderbolt alternate mode support
usb: typec: hd3ss3220: Check if regulator needs to be switched
usb: phy: tegra: parametrize PORTSC1 register offset
usb: phy: tegra: parametrize HSIC PTS value
usb: phy: tegra: return error value from utmi_wait_register
usb: phy: tegra: cosmetic fixes
dt-bindings: usb: renesas,usbhs: Add RZ/G3E SoC support
usb: dwc2: fix resume failure if dr_mode is host
usb: cdns3: fix role switching during resume
usb: dwc3: gadget: Move vbus draw to workqueue context
USB: serial: option: add Telit FN920C04 RNDIS compositions
usb: dwc3: Log dwc3 address in traces
usb: gadget: tegra-xudc: Add handling for BLCG_COREPLL_PWRDN
usb: phy: tegra: add HSIC support
usb: phy: tegra: use phy type directly
usb: typec: ucsi: Enforce mode selection for cros_ec_ucsi
usb: typec: ucsi: Support mode selection to activate altmodes
usb: typec: Introduce mode_selection bit
usb: typec: Implement mode selection
usb: typec: Expose alternate mode priority via sysfs
...
Pull devicetree updates from Rob Herring:
"DT core:
- Sync dtc/libfdt with upstream v1.7.2-62-ga26ef6400bd8
- Add a for_each_compatible_node_scoped() loop and convert users in
cpufreq, dmaengine, clk, cdx, powerpc and Arm
- Simplify of/platform.c with scoped loop helpers
- Add fw_devlink tracking for "mmc-pwrseq"
- Optimize fw_devlink callback code size for pinctrl-N properties
- Replace strcmp_suffix() with strends()
DT bindings:
- Support building single binding targets
- Convert google,goldfish-fb, cznic,turris-mox-rwtm, ti,prm-inst
- Add bindings for Freescale AVIC, Realtek RTD1xxx system
controllers, Microchip 25AA010A EEPROM, OnSemi FIN3385, IEI
WT61P803 PUZZLE, Delta Electronics DPS-800-AB power supply,
Infineon IR35221 Digital Multi-phase Controller, Infineon PXE1610
Digital Dual Output 6+1 VR12.5 & VR13 CPU Controller,
socionext,uniphier-smpctrl, and xlnx,zynqmp-firmware
- Lots of trivial binding fixes to address warnings in DTS files.
These are mostly for arm64 platforms which is getting closer to be
warning free. Some public shaming has helped.
- Fix I2C bus node names in examples
- Drop obsolete brcm,vulcan-soc binding
- Drop unreferenced binding headers"
* tag 'devicetree-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (60 commits)
dt-bindings: interrupt-controller: Add compatiblie string fsl,imx(1|25|27|31|35)-avic
dt-bindings: soc: imx: add fsl,aips and fsl,emi compatible strings
dt-bindings: display: bridge: lt8912b: Drop reset gpio requirement
dt-bindings: firmware: fsl,scu: Mark multi-channel MU layouts as deprecated
cpufreq: s5pv210: Simplify with scoped for each OF child loop
dmaengine: fsl_raid: Simplify with scoped for each OF child loop
clk: imx: imx31: Simplify with scoped for each OF child loop
clk: imx: imx27: Simplify with scoped for each OF child loop
cdx: Use mutex guard to simplify error handling
cdx: Simplify with scoped for each OF child loop
powerpc/wii: Simplify with scoped for each OF child loop
powerpc/fsp2: Simplify with scoped for each OF child loop
ARM: exynos: Simplify with scoped for each OF child loop
ARM: at91: Simplify with scoped for each OF child loop
of: Add for_each_compatible_node_scoped() helper
dt-bindings: Fix emails with spaces or missing brackets
scripts/dtc: Update to upstream version v1.7.2-62-ga26ef6400bd8
dt-bindings: crypto: inside-secure,safexcel: Mandate only ring IRQs
dt-bindings: crypto: inside-secure,safexcel: Add SoC compatibles
of: reserved_mem: Fix placement of __free() annotation
...
The WCH CH334/CH335[0] are USB2.0 protocol compliant 4-port USB HUB
controller chips, supporting USB2.0 high-speed and full-speed for
upstream ports, and USB2.0 high-speed 480Mbps, full-speed 12Mbps and
low-speed 1.5Mbps for downstream ports, supporting not only low-cost STT
mode (single TT schedules 4 downstream ports in time share), but also
supports high performance MTT mode (4 TTs each corresponding to 1 port,
concurrent processing).
Add a device tree binding for it.
[0]: https://www.wch-ic.com/downloads/CH334DS1_PDF.html
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260113095827.115-2-kernel@airkyi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the reference manual, MSM8994 does have QUSB2 PHY and does
not have DP/DM IRQs interrupts. It is also logical it has the same
constraints as similar device: MSM8996.
This fixes dtbs_check warnings like:
msm8994-sony-xperia-kitakami-karin.dtb: usb@f92f8800 (qcom,msm8994-dwc3): interrupt-names:1: 'hs_phy_irq' was expected
msm8994-sony-xperia-kitakami-karin.dtb: usb@f92f8800 (qcom,msm8994-dwc3): interrupt-names:2: 'dp_hs_phy_irq' was expected
msm8994-sony-xperia-kitakami-karin.dtb: usb@f92f8800 (qcom,msm8994-dwc3): interrupt-names:3: 'dm_hs_phy_irq' was expected
Fixes: 53c6d854be ("dt-bindings: usb: dwc3: Clean up hs_phy_irq in binding")
Fixes: 6e762f7b8e ("dt-bindings: usb: Introduce qcom,snps-dwc3")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260106185012.19551-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the device tree bindings for the DWC3 USB controller found in
Google Tensor SoCs, starting with the G5 generation (codename: laguna).
The Tensor G5 silicon represents a complete architectural departure from
previous generations (like gs101), including entirely new clock/reset
schemes, top-level wrapper and register interface. Consequently,
existing Samsung/Exynos DWC3 USB bindings are incompatible, necessitating
this new device tree binding.
The USB controller on Tensor G5 is based on Synopsys DWC3 IP and features
Dual-Role Device single port with hibernation support.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://patch.msgid.link/20251218-controller-v10-1-4047c9077274@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
6.19-rc1. Nothing major here, just lots of tiny updates for most of
the common USB drivers. Included in here are:
- more xhci driver updates and fixes
- Thunderbolt driver cleanups
- usb serial driver updates
- typec driver updates
- USB tracepoint additions
- dwc3 driver updates, including support for Apple hardware
- lots of other smaller driver updates and cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (161 commits)
usb: gadget: tegra-xudc: Always reinitialize data toggle when clear halt
USB: serial: option: move Telit 0x10c7 composition in the right place
USB: serial: option: add Telit Cinterion FE910C04 new compositions
usb: typec: ucsi: fix use-after-free caused by uec->work
usb: typec: ucsi: fix probe failure in gaokun_ucsi_probe()
usb: dwc3: core: Remove redundant comment in core init
usb: phy: Initialize struct usb_phy list_head
USB: serial: option: add Foxconn T99W760
usb: usb-storage: No additional quirks need to be added to the EL-R12 optical drive.
usb: typec: hd3ss3220: Enable VBUS based on ID pin state
dt-bindings: usb: ti,hd3ss3220: Add support for VBUS based on ID state
usb: typec: anx7411: add WQ_PERCPU to alloc_workqueue users
USB: add WQ_PERCPU to alloc_workqueue users
dt-bindings: usb: dwc3-xilinx: Describe the reset constraint for the versal platform
drivers/usb/storage: use min() instead of min_t()
usb: raw-gadget: cap raw_io transfer length to KMALLOC_MAX_SIZE
usb: ohci-da8xx: remove unused platform data
usb: gadget: functionfs: use dma_buf_unmap_attachment_unlocked() helper
usb: uas: reduce time under spinlock
usb: dwc3: eic7700: Add EIC7700 USB driver
...
Pull SoC devicetree updates from Arnd Bergmann:
"Three new SoCs got added in existing arm64 chip families:
- Renesas R-Car X5H (R8A78000) is a new generation of automotive
SoCs, based on 16 Cortex-A720 (Armv9.2) cores, which makes the the
currently highest-perforance embedded SoC.
- TI AM62L is a new variant of the AM62 family of industrial SoCs,
this one comes without a GPU.
- Qualcomm MSM8937 (Snapdragon 430) is an older mobile phone chip
based on Cortex-A53, and closely related to MSM8917 (Snapdragn
425), which we already support.
In addition, there are a good number of newly supported machines
across SoC families:
- Two Aspeed AST2600 (Cortex-A7) based BMC setups for large servers
- Mobile Phones and tables based on Mediatek MT6582, Nvidia Tegra124,
Qualcomm MSM8937 and Qualcomm MSM8939,
- Two Laptops based on Qualcomm SoCs: one using the older sdm850, the
other using x1p42100.
- One Router based on Rockchips RK3568
- 24 variants of the Enclustra Mercury system-on-module, all based on
32-bit Intel/Altera SocFPGA chips, plus two boards using 64-bit
SocFPGA Agilex chips..
- 30 industrial/embedded boards and single-board computers, using
various chips from NXP, Rockchips, Mediatek, TI, Amlogic, Qualcomm,
Spacemit, and Starfive.
In total there are 783 commits here, the majority of these improving
hardware support and cleaning up devicetree files across the tree,
with the majority of the changes going into the Qualcomm, NXP, Renesas
and Rockchips platforms"
* tag 'soc-dt-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (782 commits)
arm64: dts: mediatek: mt8195: Fix address range for JPEG decoder core 1
ARM: dts: samsung: exynos4412-midas: turn off SDIO WLAN chip during system suspend
ARM: dts: samsung: exynos4210-trats: turn off SDIO WLAN chip during system suspend
ARM: dts: samsung: exynos4210-i9100: turn off SDIO WLAN chip during system suspend
ARM: dts: samsung: universal_c210: turn off SDIO WLAN chip during system suspend
arm64: dts: amlogic: meson-g12b: Fix L2 cache reference for S922X CPUs
arm64: dts: Add gpio_intc node for Amlogic S7D SoCs
arm64: dts: Add gpio_intc node for Amlogic S7 SoCs
arm64: dts: Add gpio_intc node for Amlogic S6 SoCs
arm64: dts: amlogic: s7d: add ao secure node
arm64: dts: amlogic: s7: add ao secure node
arm64: dts: amlogic: s6: add ao secure node
arm64: dts: amlogic: Fix the register name of the 'DBI' region
dts: arm64: amlogic: add a5 pinctrl node
arm64: dts: amlogic: s7d: add power domain controller node
arm64: dts: amlogic: s7: add power domain controller node
arm64: dts: amlogic: s6: add power domain controller node
dts: arm64: amlogic: Add ISP related nodes for C3
arm64: dts: meson: add initial device-tree for Tanix TX9 Pro
dt-bindings: arm: amlogic: add support for Tanix TX9 Pro
...
Pull devicetree updates from Rob Herring:
"DT bindings:
- Convert lattice,ice40-fpga-mgr, apm,xgene-storm-dma,
brcm,sr-thermal, amazon,al-thermal, brcm,ocotp, mt8173-mdp, Actions
Owl SPS, Marvell AP80x System Controller, Marvell CP110 System
Controller, cznic,moxtet, and apm,xgene-slimpro-mbox to DT schema
format
- Add i.MX95 fsl,irqsteer, MT8365 Mali Bifrost GPU, Anvo ANV32C81W
EEPROM, and Microchip pic64gx PLIC
- Add missing LGE, AMD Seattle, and APM X-Gene SoC platform
compatibles
- Updates to brcm,bcm2836-l1-intc, brcm,bcm2835-hvs, and bcm2711-hdmi
bindings to fix warnings on BCM2712 platforms
- Drop obsolete db8500-thermal.txt
- Treewide clean-up of extra blank lines and inconsistent quoting
- Ensure all .dtbo targets are applied to a base .dtb
- Speed up dt_binding_check by skipping running validation on empty
examples
DT core:
- Add of_machine_device_match() and of_machine_get_match_data()
helpers and convert users treewide
- Fix bounds checking of address properties in FDT code. Rework the
code to have a single implementation of the bounds checks.
- Rework of_irq_init() to ignore any implicit interrupt-parent (i.e.
in a parent node) on nodes without an interrupt. This matches the
spec description and fixes some RISC-V platforms.
- Avoid a spurious message on overlay removal
- Skip DT kunit tests on RISCV+ACPI"
* tag 'devicetree-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: kbuild: Skip validating empty examples
dt-bindings: interrupt-controller: brcm,bcm2836-l1-intc: Drop interrupt-controller requirement
dt-bindings: display: Fix brcm,bcm2835-hvs bindings for BCM2712
dt-bindings: display: bcm2711-hdmi: Add interrupt details for BCM2712
of: Skip devicetree kunit tests when RISCV+ACPI doesn't populate root node
soc: tegra: Simplify with of_machine_device_match()
soc: qcom: ubwc: Simplify with of_machine_get_match_data()
powercap: dtpm: Simplify with of_machine_get_match_data()
platform: surface: Simplify with of_machine_get_match_data()
irqchip/atmel-aic: Simplify with of_machine_get_match_data()
firmware: qcom: scm: Simplify with of_machine_device_match()
cpuidle: big_little: Simplify with of_machine_device_match()
cpufreq: sun50i: Simplify with of_machine_device_match()
cpufreq: mediatek: Simplify with of_machine_get_match_data()
cpufreq: dt-platdev: Simplify with of_machine_get_match_data()
of: Add wrappers to match root node with OF device ID tables
dt-bindings: eeprom: at25: Add Anvo ANV32C81W
of/reserved_mem: Simplify the logic of __reserved_mem_alloc_size()
of/reserved_mem: Simplify the logic of fdt_scan_reserved_mem_reg_nodes()
of/reserved_mem: Simplify the logic of __reserved_mem_reserve_reg()
...
