The cited commit aimed to ensure that Virtual Functions (VFs) assign a
queue affinity to a Queue Pair (QP) to distribute traffic when
the LAG master creates a hardware LAG. If the affinity was set while
the hardware was not in LAG, the firmware would ignore the affinity value.
However, this commit unintentionally assigned an affinity to QPs on the LAG
master's VPORT even if the RDMA device was not marked as LAG-enabled.
In most cases, this was not an issue because when the hardware entered
hardware LAG configuration, the RDMA device of the LAG master would be
destroyed and a new one would be created, marked as LAG-enabled.
The problem arises when a user configures Equal-Cost Multipath (ECMP).
In ECMP mode, traffic can be directed to different physical ports based on
the queue affinity, which is intended for use by VPORTS other than the
E-Switch manager. ECMP mode is supported only if both E-Switch managers are
in switchdev mode and the appropriate route is configured via IP. In this
configuration, the RDMA device is not destroyed, and we retain the RDMA
device that is not marked as LAG-enabled.
To ensure correct behavior, Send Queues (SQs) opened by the E-Switch
manager through verbs should be assigned strict affinity. This means they
will only be able to communicate through the native physical port
associated with the E-Switch manager. This will prevent the firmware from
assigning affinity and will not allow the SQs to be remapped in case of
failover.
Fixes: 802dcc7fc5 ("RDMA/mlx5: Support TX port affinity for VF drivers in LAG mode")
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://lore.kernel.org/r/425b05f4da840bc684b0f7e8ebf61aeb5cef09b0.1685960567.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for the Qualcomm Snapdragon
platforms.
There are bug fixes for error handling in Qualcomm icc-bwmon,
rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
firmware driver and a missing initialization in the Arm ff-a firmware
driver. The Qualcomm RPMh and EDAC drivers need some rework to work
correctly on all supported chips.
The DT fixes include:
- i.MX8 fixes for gpio, pinmux and clock settings
- ADS touchscreen gpio polarity settings in several machines
- Address dtb warnings for caches, panel and input-enable properties
on Qualcomm platforms
- Incorrect data on qualcomm platforms fir SA8155P power domains,
SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire
- Remoteproc firmware paths are corrected for Sony Xperia 10 IV"
* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
firmware: arm_ffa: Set handle field to zero in memory descriptor
ARM: dts: Fix erroneous ADS touchscreen polarities
arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
EDAC/qcom: Get rid of hardcoded register offsets
EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
dt-bindings: cache: qcom,llcc: Fix SM8550 description
arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
soc: qcom: rpmhpd: Add SA8155P power domains
arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
dt-bindings: power: qcom,rpmpd: Add SA8155P
soc: qcom: Rename ice to qcom_ice to avoid module name conflict
soc: qcom: rmtfs: Fix error code in probe()
soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
ARM: at91: pm: fix imbalanced reference counter for ethernet devices
arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
...
netfilter pull request 23-06-08
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for net:
1) Add commit and abort set operation to pipapo set abort path.
2) Bail out immediately in case of ENOMEM in nfnetlink batch.
3) Incorrect error path handling when creating a new rule leads to
dangling pointer in set transaction list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On MSM8996 two CPU clusters are interconnected using the Core Bus
Fabric (CBF). In order for the CPU clusters to function properly, it
should be clocked following the core's frequencies to provide adequate
bandwidth.
Register CBF as a clock (required for CPU to boot) and add a tiny
interconnect layer on top of it to let cpufreq/opp scale the CBF clock.
* icc-cbf
dt-bindings: interconnect/msm8996-cbf: add defines to be used by CBF
interconnect: add clk-based icc provider support
clk: qcom: cbf-msm8996: scale CBF clock according to the CPUfreq
interconnect: icc-clk: fix modular build
Link: https://lore.kernel.org/r/20230512001334.2983048-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Kalle Valo says:
====================
wireless-next patches for v6.5
The second pull request for v6.5. We have support for three new
Realtek chipsets, all from different generations. Shows how active
Realtek development is right now, even older generations are being
worked on.
Note: We merged wireless into wireless-next to avoid complex conflicts
between the trees.
Major changes:
rtl8xxxu
- RTL8192FU support
rtw89
- RTL8851BE support
rtw88
- RTL8723DS support
ath11k
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID
Advertisement (EMA) support in AP mode
iwlwifi
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
cfg80211/mac80211
- more Multi-Link Operation (MLO) support such as hardware restart
- fixes for a potential work/mutex deadlock and with it beginnings of
the previously discussed locking simplifications
* tag 'wireless-next-2023-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (162 commits)
wifi: rtlwifi: remove misused flag from HAL data
wifi: rtlwifi: remove unused dualmac control leftovers
wifi: rtlwifi: remove unused timer and related code
wifi: rsi: Do not set MMC_PM_KEEP_POWER in shutdown
wifi: rsi: Do not configure WoWlan in shutdown hook if not enabled
wifi: brcmfmac: Detect corner error case earlier with log
wifi: rtw89: 8852c: update RF radio A/B parameters to R63
wifi: rtw89: 8852c: update TX power tables to R63 with 6 GHz power type (3 of 3)
wifi: rtw89: 8852c: update TX power tables to R63 with 6 GHz power type (2 of 3)
wifi: rtw89: 8852c: update TX power tables to R63 with 6 GHz power type (1 of 3)
wifi: rtw89: process regulatory for 6 GHz power type
wifi: rtw89: regd: update regulatory map to R64-R40
wifi: rtw89: regd: judge 6 GHz according to chip and BIOS
wifi: rtw89: refine clearing supported bands to check 2/5 GHz first
wifi: rtw89: 8851b: configure CRASH_TRIGGER feature for 8851B
wifi: rtw89: set TX power without precondition during setting channel
wifi: rtw89: debug: txpwr table access only valid page according to chip
wifi: rtw89: 8851b: enable hw_scan support
wifi: cfg80211: move scan done work to wiphy work
wifi: cfg80211: move sched scan stop to wiphy work
...
====================
Link: https://lore.kernel.org/r/87bkhohkbg.fsf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the embedded cpu supports SRIOV it can be enabled and disabled
independently from the host SRIOV. Track the pages separately so we can
properly wait for returned VF pages.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
These functions are for query/set by vport, there was an underlying
assumption that vport was equal to function ID. That's not the case for
EC VF functions. Set the ec_vf_function bit accordingly.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add ec_vf_vport_base to HCA Capabilities 2. This indicates the base vport
of embedded CPU virtual functions that are connected to the eswitch.
Add ec_vf_function to query/set_hca_caps. If set this indicates
accessing a virtual function on the embedded CPU by function ID. This
should only be used with other_function set to 1.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The sys_ni_posix_timers() definition causes a warning when the declaration
is missing, so this needs to be added along with the normal syscalls,
outside of the #ifdef.
kernel/time/posix-stubs.c:26:17: error: no previous prototype for 'sys_ni_posix_timers' [-Werror=missing-prototypes]
Link: https://lkml.kernel.org/r/20230607142925.3126422-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Implement a hardlockup detector that doesn't doesn't need any extra
arch-specific support code to detect lockups. Instead of using something
arch-specific we will use the buddy system, where each CPU watches out for
another one. Specifically, each CPU will use its softlockup hrtimer to
check that the next CPU is processing hrtimer interrupts by verifying that
a counter is increasing.
NOTE: unlike the other hard lockup detectors, the buddy one can't easily
show what's happening on the CPU that locked up just by doing a simple
backtrace. It relies on some other mechanism in the system to get
information about the locked up CPUs. This could be support for NMI
backtraces like [1], it could be a mechanism for printing the PC of locked
CPUs at panic time like [2] / [3], or it could be something else. Even
though that means we still rely on arch-specific code, this arch-specific
code seems to often be implemented even on architectures that don't have a
hardlockup detector.
This style of hardlockup detector originated in some downstream Android
trees and has been rebased on / carried in ChromeOS trees for quite a long
time for use on arm and arm64 boards. Historically on these boards we've
leveraged mechanism [2] / [3] to get information about hung CPUs, but we
could move to [1].
Although the original motivation for the buddy system was for use on
systems without an arch-specific hardlockup detector, it can still be
useful to use even on systems that _do_ have an arch-specific hardlockup
detector. On x86, for instance, there is a 24-part patch series [4] in
progress switching the arch-specific hard lockup detector from a scarce
perf counter to a less-scarce hardware resource. Potentially the buddy
system could be a simpler alternative to free up the perf counter but
still get hard lockup detection.
Overall, pros (+) and cons (-) of the buddy system compared to an
arch-specific hardlockup detector (which might be implemented using
perf):
+ The buddy system is usable on systems that don't have an
arch-specific hardlockup detector, like arm32 and arm64 (though it's
being worked on for arm64 [5]).
+ The buddy system may free up scarce hardware resources.
+ If a CPU totally goes out to lunch (can't process NMIs) the buddy
system could still detect the problem (though it would be unlikely
to be able to get a stack trace).
+ The buddy system uses the same timer function to pet the hardlockup
detector on the running CPU as it uses to detect hardlockups on
other CPUs. Compared to other hardlockup detectors, this means it
generates fewer interrupts and thus is likely better able to let
CPUs stay idle longer.
- If all CPUs are hard locked up at the same time the buddy system
can't detect it.
- If we don't have SMP we can't use the buddy system.
- The buddy system needs an arch-specific mechanism (possibly NMI
backtrace) to get info about the locked up CPU.
[1] https://lore.kernel.org/r/20230419225604.21204-1-dianders@chromium.org
[2] https://issuetracker.google.com/172213129
[3] https://docs.kernel.org/trace/coresight/coresight-cpu-debug.html
[4] https://lore.kernel.org/lkml/20230301234753.28582-1-ricardo.neri-calderon@linux.intel.com/
[5] https://lore.kernel.org/linux-arm-kernel/20220903093415.15850-1-lecopzer.chen@mediatek.com/
Link: https://lkml.kernel.org/r/20230519101840.v5.14.I6bf789d21d0c3d75d382e7e51a804a7a51315f2c@changeid
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ian Rogers <irogers@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masayoshi Mizuma <msys.mizuma@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In preparation for the buddy hardlockup detector where the CPU checking
for lockup might not be the currently running CPU, add a "cpu" parameter
to watchdog_hardlockup_check().
As part of this change, make hrtimer_interrupts an atomic_t since now the
CPU incrementing the value and the CPU reading the value might be
different. Technially this could also be done with just READ_ONCE and
WRITE_ONCE, but atomic_t feels a little cleaner in this case.
While hrtimer_interrupts is made atomic_t, we change
hrtimer_interrupts_saved from "unsigned long" to "int". The "int" is
needed to match the data type backing atomic_t for hrtimer_interrupts.
Even if this changes us from 64-bits to 32-bits (which I don't think is
true for most compilers), it doesn't really matter. All we ever do is
increment it every few seconds and compare it to an old value so 32-bits
is fine (even 16-bits would be). The "signed" vs "unsigned" also doesn't
matter for simple equality comparisons.
hrtimer_interrupts_saved is _not_ switched to atomic_t nor even accessed
with READ_ONCE / WRITE_ONCE. The hrtimer_interrupts_saved is always
consistently accessed with the same CPU. NOTE: with the upcoming "buddy"
detector there is one special case. When a CPU goes offline/online then
we can change which CPU is the one to consistently access a given instance
of hrtimer_interrupts_saved. We still can't end up with a partially
updated hrtimer_interrupts_saved, however, because we end up petting all
affected CPUs to make sure the new and old CPU can't end up somehow
read/write hrtimer_interrupts_saved at the same time.
Link: https://lkml.kernel.org/r/20230519101840.v5.10.I3a7d4dd8c23ac30ee0b607d77feb6646b64825c0@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Colin Cross <ccross@android.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masayoshi Mizuma <msys.mizuma@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The perf hardlockup detector works by looking at interrupt counts and
seeing if they change from run to run. The interrupt counts are managed
by the common watchdog code via its watchdog_timer_fn().
Currently the API between the perf detector and the common code is a
function: is_hardlockup(). When the hard lockup detector sees that
function return true then it handles printing out debug info and inducing
a panic if necessary.
Let's change the API a little bit in preparation for the buddy hardlockup
detector. The buddy hardlockup detector wants to print nearly the same
debug info and have nearly the same panic behavior. That means we want to
move all that code to the common file. For now, the code in the common
file will only be there if the perf hardlockup detector is enabled, but
eventually it will be selected by a common config.
Right now, this _just_ moves the code from the perf detector file to the
common file and changes the names. It doesn't make the changes that the
buddy hardlockup detector will need and doesn't do any style cleanups. A
future patch will do cleanup to make it more obvious what changed.
With the above, we no longer have any callers of is_hardlockup() outside
of the "watchdog.c" file, so we can remove it from the header, make it
static, and move it to the same "#ifdef" block as our new
watchdog_hardlockup_check(). While doing this, it can be noted that even
if no hardlockup detectors were configured the existing code used to still
have the code for counting/checking "hrtimer_interrupts" even if the perf
hardlockup detector wasn't configured. We didn't need to do that, so move
all the "hrtimer_interrupts" counting to only be there if the perf
hardlockup detector is configured as well.
This change is expected to be a no-op.
Link: https://lkml.kernel.org/r/20230519101840.v5.8.Id4133d3183e798122dc3b6205e7852601f289071@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Colin Cross <ccross@android.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masayoshi Mizuma <msys.mizuma@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Ricardo Neri <ricardo.neri@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Tzung-Bi Shih <tzungbi@chromium.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A number of internal functions in kcov are only called from generated code
and don't technically need a declaration, but 'make W=1' warns about
global symbols without a prototype:
kernel/kcov.c:199:14: error: no previous prototype for '__sanitizer_cov_trace_pc' [-Werror=missing-prototypes]
kernel/kcov.c:264:14: error: no previous prototype for '__sanitizer_cov_trace_cmp1' [-Werror=missing-prototypes]
kernel/kcov.c:270:14: error: no previous prototype for '__sanitizer_cov_trace_cmp2' [-Werror=missing-prototypes]
kernel/kcov.c:276:14: error: no previous prototype for '__sanitizer_cov_trace_cmp4' [-Werror=missing-prototypes]
kernel/kcov.c:282:14: error: no previous prototype for '__sanitizer_cov_trace_cmp8' [-Werror=missing-prototypes]
kernel/kcov.c:288:14: error: no previous prototype for '__sanitizer_cov_trace_const_cmp1' [-Werror=missing-prototypes]
kernel/kcov.c:295:14: error: no previous prototype for '__sanitizer_cov_trace_const_cmp2' [-Werror=missing-prototypes]
kernel/kcov.c:302:14: error: no previous prototype for '__sanitizer_cov_trace_const_cmp4' [-Werror=missing-prototypes]
kernel/kcov.c:309:14: error: no previous prototype for '__sanitizer_cov_trace_const_cmp8' [-Werror=missing-prototypes]
kernel/kcov.c:316:14: error: no previous prototype for '__sanitizer_cov_trace_switch' [-Werror=missing-prototypes]
Adding prototypes for these in a header solves that problem, but now there
is a mismatch between the built-in type and the prototype on 64-bit
architectures because they expect some functions to take a 64-bit
'unsigned long' argument rather than an 'unsigned long long' u64 type:
include/linux/kcov.h:84:6: error: conflicting types for built-in function '__sanitizer_cov_trace_switch'; expected 'void(long long unsigned int, void *)' [-Werror=builtin-declaration-mismatch]
84 | void __sanitizer_cov_trace_switch(u64 val, u64 *cases);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid this as well with a custom type definition.
Link: https://lkml.kernel.org/r/20230517124944.929997-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Rong Tao <rongtao@cestc.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The init/main.c file contains some extern declarations for functions
defined in architecture code, and it defines some other functions that are
called from architecture code with a custom prototype. Both of those
result in warnings with 'make W=1':
init/calibrate.c:261:37: error: no previous prototype for 'calibrate_delay_is_known' [-Werror=missing-prototypes]
init/main.c:790:20: error: no previous prototype for 'mem_encrypt_init' [-Werror=missing-prototypes]
init/main.c:792:20: error: no previous prototype for 'poking_init' [-Werror=missing-prototypes]
arch/arm64/kernel/irq.c:122:13: error: no previous prototype for 'init_IRQ' [-Werror=missing-prototypes]
arch/arm64/kernel/time.c:55:13: error: no previous prototype for 'time_init' [-Werror=missing-prototypes]
arch/x86/kernel/process.c:935:13: error: no previous prototype for 'arch_post_acpi_subsys_init' [-Werror=missing-prototypes]
init/calibrate.c:261:37: error: no previous prototype for 'calibrate_delay_is_known' [-Werror=missing-prototypes]
kernel/fork.c:991:20: error: no previous prototype for 'arch_task_cache_init' [-Werror=missing-prototypes]
Add prototypes for all of these in include/linux/init.h or another
appropriate header, and remove the duplicate declarations from
architecture specific code.
[sfr@canb.auug.org.au: declare time_init_early()]
Link: https://lkml.kernel.org/r/20230519124311.5167221c@canb.auug.org.au
Link: https://lkml.kernel.org/r/20230517131102.934196-12-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/gup: disallow GUP writing to file-backed mappings by
default", v9.
Writing to file-backed mappings which require folio dirty tracking using
GUP is a fundamentally broken operation, as kernel write access to GUP
mappings do not adhere to the semantics expected by a file system.
A GUP caller uses the direct mapping to access the folio, which does not
cause write notify to trigger, nor does it enforce that the caller marks
the folio dirty.
The problem arises when, after an initial write to the folio, writeback
results in the folio being cleaned and then the caller, via the GUP
interface, writes to the folio again.
As a result of the use of this secondary, direct, mapping to the folio no
write notify will occur, and if the caller does mark the folio dirty, this
will be done so unexpectedly.
For example, consider the following scenario:-
1. A folio is written to via GUP which write-faults the memory, notifying
the file system and dirtying the folio.
2. Later, writeback is triggered, resulting in the folio being cleaned and
the PTE being marked read-only.
3. The GUP caller writes to the folio, as it is mapped read/write via the
direct mapping.
4. The GUP caller, now done with the page, unpins it and sets it dirty
(though it does not have to).
This change updates both the PUP FOLL_LONGTERM slow and fast APIs. As
pin_user_pages_fast_only() does not exist, we can rely on a slightly
imperfect whitelisting in the PUP-fast case and fall back to the slow case
should this fail.
This patch (of 3):
vma_wants_writenotify() is specifically intended for setting PTE page
table flags, accounting for existing page table flag state and whether the
underlying filesystem performs dirty tracking for a file-backed mapping.
Everything is predicated firstly on whether the mapping is shared
writable, as this is the only instance where dirty tracking is pertinent -
MAP_PRIVATE mappings will always be CoW'd and unshared, and read-only
file-backed shared mappings cannot be written to, even with FOLL_FORCE.
All other checks are in line with existing logic, though now separated
into checks eplicitily for dirty tracking and those for determining how to
set page table flags.
We make this change so we can perform checks in the GUP logic to determine
which mappings might be problematic when written to.
Link: https://lkml.kernel.org/r/cover.1683235180.git.lstoakes@gmail.com
Link: https://lkml.kernel.org/r/0f218370bd49b4e6bbfbb499f7c7b92c26ba1ceb.1683235180.git.lstoakes@gmail.com
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Mika Penttilä <mpenttil@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Kirill A . Shutemov <kirill@shutemov.name>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
