this is used to be compatible with old SoCs, such as mt8195, which shares
t-phy between usb3 and pcie controller, usually, it's default mode is pcie
rc mode, and could use force mode to switch into usb3 mode, because pericfg
layer doesn't provide mode switch, also no efuse or jumper can be used;
Currently, only support switch from default pcie mode to usb3;
Note: don't use this way on new SoCs, use pericfg layer's mode switch
instead (by perperty "mediatek,syscon-type").
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20231211025624.28991-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The registers, which are being touched in current SM8550 UFS PHY settings,
and the values being programmed are mainly the ones working for HS-G4 mode,
meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
However, even consider HS-G4 mode only, some of them are incorrect and some
are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.
Fixes: 1679bfef90 ("phy: qcom-qmp-ufs: Add SM8550 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/1701520577-31163-10-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy fixes from Vinod Koul:
- register offset fix for TI driver
- mediatek driver minimal supported frequency fix
- negative error code in probe fix for sunplus driver
* tag 'phy-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: sunplus: return negative error code in sp_usb_phy_probe
phy: mediatek: mipi: mt8183: fix minimal supported frequency
phy: ti: gmii-sel: Fix register offset when parent is not a syscon node
Commit 51a9b2c03d ("phy: rockchip-inno-usb2: Handle ID IRQ") added ID
detection interrupt registers. However the current implementation assumes
that falling and rising edge interrupt are always enabled in registers
spanning over subsequent bits.
That is not the case for RK3128's version of the phy and this
implementation can't be used as-is, since there are bits with different
purpose in between.
This splits up the register definitions for id_det_en, id_det_en and
id_det_clr registers in rising and falling edge variants.
It's required as preparation to support RK3128's Innosilicon usb2 phy as
well in this driver and matches pretty much to what the vendor does, so I'm
not expecting issues for other SoCs with that change.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231119121340.109025-2-knaerzche@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the node for this phy selector is a child node of a syscon node then the
property 'reg' is used as an offset into the parent regmap. When the node
is standalone and gets its own regmap this offset is pre-applied. So we need
to track which method was used to get the regmap and not apply the offset
in the standalone case.
Fixes: 1fdfa7cccd ("phy: ti: gmii-sel: Allow parent to not be syscon node")
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231025143302.1265633-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This reverts commit 134e6d25f6.
The recently added Realtek PHY drivers depend on the new port status
notification mechanism which was built on the deprecated USB PHY
implementation and devicetree binding.
Specifically, using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property which is clearly wrong.
We should not be building new functionality on top of the legacy USB PHY
implementation even if it is currently stuck in some kind of
transitional limbo.
Revert the new Realtek PHY drivers for now so that the port status
notification interface can be reverted and replaced.
Fixes: 134e6d25f6 ("phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY")
Cc: stable@vger.kernel.org # 6.6
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231106110654.31090-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit adda6e82a7.
The recently added Realtek PHY drivers depend on the new port status
notification mechanism which was built on the deprecated USB PHY
implementation and devicetree binding.
Specifically, using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property which is clearly wrong.
We should not be building new functionality on top of the legacy USB PHY
implementation even if it is currently stuck in some kind of
transitional limbo.
Revert the new Realtek PHY drivers for now so that the port status
notification interface can be reverted and replaced.
Fixes: adda6e82a7 ("phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY")
Cc: stable@vger.kernel.org # 6.6
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231106110654.31090-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other and pull in various other headers. In
preparation to fix this, adjust the includes for what is actually needed.
of_device.h isn't needed, but platform_device.h was implicitly included by
it.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231010205701.1585026-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With gcc 12.3.0, when this file is built, we get errors such as:
drivers/phy/allwinner/phy-sun4i-usb.c: In function ‘sun4i_usb_phy_probe’:
drivers/phy/allwinner/phy-sun4i-usb.c:790:52: error: ‘_vbus’ directive output may be truncated writing 5 bytes into a region of size between 2 and 12 [-Werror=format-truncation=]
790 | snprintf(name, sizeof(name), "usb%d_vbus", i);
| ^~~~~
drivers/phy/allwinner/phy-sun4i-usb.c:790:17: note: ‘snprintf’ output between 10 and 20 bytes into a destination of size 16
790 | snprintf(name, sizeof(name), "usb%d_vbus", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Because of the possible value of 'i', this can't be an issue in real world
application, but in order to have "make W=1" work correctly, give more
space for 'name'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/0bc81612171baaa6d5dff58c8e009debc03e1ba8.1693735840.git.christophe.jaillet@wanadoo.fr
[vkoul: updated patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
