The goal of writing 0x6954341e / 0x6955341e to REG_OFDM0_XA_AGC_CORE1
appears to be setting the initial gain, which is stored in bits 0..6.
Bits 7..31 are the same as what the phy init tables write.
Modify only bits 0..6 so that we don't have to care about the values
of the others. This way we don't have to add another "else if" for the
RTL8192FU.
Why we need to change the initial gain from the default 0x20 to 0x1e?
Not sure. Some of the vendor drivers change it to 0x1e before scanning
and then restore it to the original value after.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/cf91ca69-70e3-4c20-c0b1-e59d452356a1@gmail.com
Most devices have a vendor name, product name, and serial number in the
efuse, but it's pretty useless. It duplicates the information already
printed by the USB subsystem:
usb 1-4: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n WLAN Adapter
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00e04c000001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n WLAN Adapter
usb 1-4: New USB device found, idVendor=0bda, idProduct=818b, bcdDevice= 2.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n NIC
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00e04c000001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n NIC
-> usb 1-4: Serial not available.
usb 1-4: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 002E2DC0041F
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n
usb 1-4: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 802.11n NIC
usb 1-4: Manufacturer: Realtek
usb 1-4: SerialNumber: 00E04C0001
-> usb 1-4: Vendor: Realtek
-> usb 1-4: Product: 802.11n NIC
-> usb 1-4: Serial: 00E04C0001
Also, that data is not interpreted correctly in all cases:
usb 3-1.1.2: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00
usb 3-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1.1.2: Product: 802.11n NIC
usb 3-1.1.2: Manufacturer: Realtek
usb 3-1.1.2: Vendor: Realtek
usb 3-1.1.2: Product: \x03802.11n NI
usb 3-1.1.2: Serial: \xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217231
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a2a7d9df-0529-7890-3522-48dce613753f@gmail.com
According to the vendor driver the pkg_type has to be set to '1'
for some rtw8821c variants. As the pkg_type has been hardcoded to
'0', add a field for it in struct rtw_hal and set this correctly
in the rtw8821c part.
With this parsing of a rtw_table is influenced and check_positive()
in phy.c returns true for some cases here. The same is done in the
vendor driver. However, this has no visible effect on the driver
here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-4-s.hauer@pengutronix.de
On my RTW8821CU chipset rfe_option reads as 0x22. Looking at the
vendor driver suggests that the field width of rfe_option is 5 bit,
so rfe_option should be masked with 0x1f.
Without this the rfe_option comparisons with 2 further down the
driver evaluate as false when they should really evaluate as true.
The effect is that 2G channels do not work.
rfe_option is also used as an array index into rtw8821c_rfe_defs[].
rtw8821c_rfe_defs[34] (0x22) was added as part of adding USB support,
likely because rfe_option reads as 0x22. As this now becomes 0x2,
rtw8821c_rfe_defs[34] is no longer used and can be removed.
Note that this might not be the whole truth. In the vendor driver
there are indeed places where the unmasked rfe_option value is used.
However, the driver has several places where rfe_option is tested
with the pattern if (rfe_option == 2 || rfe_option == 0x22) or
if (rfe_option == 4 || rfe_option == 0x24), so that rfe_option BIT(5)
has no influence on the code path taken. We therefore mask BIT(5)
out from rfe_option entirely until this assumption is proved wrong
by some chip variant we do not know yet.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-3-s.hauer@pengutronix.de
The RTW88 chipsets have four different priority queues in hardware. For
the USB type chipsets the packets destined for a specific priority queue
must be sent through the endpoint corresponding to the queue. This was
not fully understood when porting from the RTW88 USB out of tree driver
and thus violated.
This patch implements the qsel to endpoint mapping as in
get_usb_bulkout_id_88xx() in the downstream driver.
Without this the driver often issues "timed out to flush queue 3"
warnings and often TX stalls completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: ValdikSS <iam@valdikss.org.ru>
Tested-by: Alexandru gagniuc <mr.nuke.me@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230417140358.2240429-2-s.hauer@pengutronix.de
This patch allows vifs sharing same hardware with the AP mode vif to
do scan, do note that this could lead to packet loss or disconnection
of the AP's clients. Since we don't have chanctx, update scan info
upon set channel so bandwidth changes won't go unnoticed and get
misconfigured after scan. Download beacon just before scan starts to
allow hardware to get proper content to do beaconing. Last, beacons
should only be transmitted in AP's operating channel. Turn related
beacon functions off while we're in other channels so the receiving
stations won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121323.18008-1-pkshih@realtek.com
Only gather reserved pages from AP interface after it has started. Or
else ieee80211_beacon_get_*() returns NULL and causes other VIFs'
reserved pages fail to download. Update location of current reserved page
after beacon renews so offsets changed by beacon can be recognized.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121300.17900-1-pkshih@realtek.com
Extend 8822c's reserved page number to accommodate additional required
pages. Reserved page is an area of memory in the FIFO dedicated for
special purposes. Previously only one interface is supported so 8 pages
should suffice, extend it so we can support 2 interfaces concurrently.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-4-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALBB_029_106_15 (V17)
- HALRF_029_00_089
* Radio A 0x22
* NCTL 0x5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-3-pkshih@realtek.com
These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.
Internal version of these tables:
- HALBB_029_106_15 (V17)
- HALRF_029_00_089
* Radio A 0x22
* NCTL 0x5
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-2-pkshih@realtek.com
One chip can have different RFE (RF front end) types which we will judge
at runtime. And, different RFE types may use different RF parameter tables.
Though we didn't really meet this case previously, we are going to meet it
on upcoming chip RTL8851B. So, this commit handles parameter tables for
runtime RFE type.
We now encapsulate rtw89_txpwr_rule_<2/5/6>ghz tables into rtw89_rfe_parms.
Then, each chip defines its default parameter tables, and if needed, it can
configure extra parameter tables by RFE type. Finally we determine runtime
parameter tables by RFE type if one is configured. Otherwise, we use the
default parameter tables.
For now, we just move all settings under default parameter tables. We will
configure parameter tables by RFE types in separate commits afterwards.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330080331.37155-1-pkshih@realtek.com
In the discuss threads [1] [2], new firmware format break user space
because older drivers can't recognize new firmware format. To avoid this,
the new format will be named rtw89/rtw8852b_fw-1.bin and only new driver
try to load it. Old drivers only load original and understandable firmware
rtw89/rtw8852b_fw.bin.
More, new driver will be still backward compatible with old firmware, so
original firmware can be used by new driver.
If there is newer firmware format is introduced, rtw89/rtw8852b_fw-2.bin
will be given. The same rules will be applied like above. So, we will have
firmware like below in linux-firmware in the future.
rtw89/rtw8852b_fw-2.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852b_fw.bin
After this patch, MODULE_FIRMWARE() of 8852A/B/C become
rtw89/rtw8852a_fw.bin
rtw89/rtw8852b_fw-1.bin
rtw89/rtw8852c_fw.bin
[1] https://lore.kernel.org/linux-wireless/df1ce994-3368-a57e-7078-8bdcccf4a1fd@gmail.com/T/#m24cb43be31a762d0ea70bf07f27ae96c59f6931b
[2] https://bugzilla.kernel.org/show_bug.cgi?id=217207
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-4-pkshih@realtek.com
Since we are going to load more than one firmware and some are not
presented or optional, using asynchronous API request_firmware_nowait()
will become complicated. Also, we want to use firmware_request_nowarn()
to avoid warning messages when loading optional files. So, use
schedule_work to be simpler.
To abstract loading a firmware or file, define a struct rtw89_fw_req_info
containing a struct firmware and a completion to ensure this firmware is
loaded completely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-3-pkshih@realtek.com
In early feature bitmap obtained from rtw89_early_fw_feature_recognize(),
the bits needed to check get increased. It's more friendly to work with
RTW89_CHK_FW_FEATURE(). So, we concentrate the flow of iterating FW feature
configures and calling RTW89_SET_FW_FEATURE() for various uses. And then,
we adjust rtw89_early_fw_feature_recognize() for RTW89_CHK_FW_FEATURE().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-2-pkshih@realtek.com
We used to store operating channel info after associated. However, scan
might happen before that. Without switching back to operating channel,
authentication or association might fail. Therefore, we switch back to
operating channel when the scanning vif's BSSID is non-zero, which
implies connected or during attempt to connect.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-6-pkshih@realtek.com
Use POWER_ON flag to make sure power on/off is symmetric. Since both
remain_on_channel and hw_scan both alter the power state, this makes
sure that we don't enter/leave IPS mode twice.
Also, replace IPS related functions with inline function that does
similar logic so we can track it more easily.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-5-pkshih@realtek.com
Add support of remain on channel ops. Since channel context is
required to enable multi-channel concurrent(MCC) and the current
ROC in mac80211 don't support more than 1 channel context, add this
to let P2P and other protocols relying on this work as expected.
The off-channel duration and cancel timing is purely controlled by
upper layers.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-4-pkshih@realtek.com
Allocate a per-skb completion to track those skbs we are interested in
and wait for them to complete transmission with TX status.
Normally, the completion object is freed by wait side, but it could be
timeout result that complete side should free the object instead. Add a
owner field with RCU to determine which side should free the object.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-3-pkshih@realtek.com
