Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.
Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.
SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.
Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.
To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.
This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.
(1) make sure that events are generated only for VFs sitting on
the relevant physical port (under the ALL_SLAVES flow).
(2) before generating the event, convert from physical (one or two)
to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).
This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.
So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.
Fixes: 449fc48866 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.
It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.
Fixes: 449fc48866 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.
Currently the sleep threshold/grace period is at a
very conservative value of 60ms.
Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.
Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.
The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.
This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is actually safe to enable ASPM after the
device is booted up.
This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.
Fixes: dc16427bbe ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just two small DP fixes for 4.1
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
Pull two xen bugfixes from David Vrabel:
- fix ARM build regression.
- fix VIRQ_CONSOLE related oops.
* tag 'for-linus-4.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't bind non-percpu VIRQs with percpu chip
xen/arm: Define xen_arch_suspend()
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
Pull thermal fixes from Zhang Rui:
"Three fixes for Armada (380) and TI (dra7 and OMAP5) thermal soc
drivers"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: armada: Update Armada 380 thermal sensor coefficients
thermal: ti-soc-thermal: OMAP5: Implement Workaround for Errata i813
thermal: ti-soc-thermal: dra7: Implement Workaround for Errata i814
Pull infiniband/rdma fixes from Doug Ledford:
"This should hopefully be the last request for 4.1-rc for the RDMA
stack. It contains some late ocrdma fixes that I'm including because
they are small and self contained. It also contains two bug fixes
that are simple and easily verified.
Summary:
- a number of small, well contained bug fixes for ocrdma driver
- a simple fix for the connection negotiation sequence on IB
- fix for broken AF_IB address on UD queue pair support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cma: Fix broken AF_IB UD support
ib/cm: Change reject message type when destroying cm_id
RDMA/ocrdma: Update ocrdma version number
RDMA/ocrdma: Fail connection for MTU lesser than 512
RDMA/ocrdma: Fix dmac resolution for link local address
RDMA/ocrdma: Prevent allocation of DPP PDs if FW doesnt support it
RDMA/ocrdma: Fix the request length for RDMA_QUERY_QP mailbox command to FW.
RDMA/ocrdma: Use VID 0 if PFC is enabled and vlan is not configured
RDMA/ocrdma: Fix QP state transition in destroy_qp
RDMA/ocrdma: Report EQ full fatal error
RDMA/ocrdma: Fix EQ destroy failure during driver unload
Pull MMC fix from Ulf Hansson:
"One more mmc fix intended for v4.1 rc5:
MMC host:
- atmel-mci: fix bad variable type for clkdiv"
* tag 'mmc-4.1-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: atmel-mci: fix bad variable type for clkdiv
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the caller already check the presence of a of_node there
is no need to repeat the check in stmmac_probe_config_dt.
There is also no point in checking the return value of the
of_match_device function since if there wasn't match in the
first place we would never be in this function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stmmac_dvr_probe takes care of setting driver data and
assign resources to the priv structure there is no need to
access the priv structure from the other probe functions.
This mean that this function can be changed into just return
an int and thus simplifying the callers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creat a struct that contain all the resources that needs to be
assigned to the priv struct in stmmac_dvr_probe. This makes it
possible to factor out more common code from the other probe
functions and also use this struct to hold the resources as
they are fetched.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting of driver data into stmmac_dvr_probe so the
other probe functions don't have to. This will help to
simplify the other probe functions later.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some T4/T5 registers that were included incorrectly.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_mac_address() NIC-type function for EF10 only, and
use this to set the MAC address on the vadaptor. For Siena and
earlier, the MAC address continues to be set by MC_CMD_SET_MAC;
this is still called on EF10, and including a MAC address in
this command has no effect.
The sriov_mac_address_changed() NIC-type function is no longer
needed on EF10, but it is needed for Siena where it is used to
update the peer address of the PF for VFDI. Change this to use
the new set_mac_address function pointer.
efx_ef10_sriov_mac_address_changed() is no longer called, as VFs
will try to change the MAC address on their vadaptor rather than
trying to change to the context of the PF to alter the vport.
When a VF is running in direct passthrough mode with MAC spoofing
enabled, it will be able to change the MAC address on its vadaptor.
In this case, there is a link to the PF, so find the correct VF in
its ef10_vf array and update the MAC address.
ndo_set_mac_address() can be called during driver unload while
bonding, and in this case the device has already been stopped, so
don't call efx_net_open() to restart it after reconfiguration.
efx->port_enabled is set to false in efx_stop_port(), so it is
indicator of whether the device needs to be restarted.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exercised with
"ip link set <PF intf> vf <vf_i> state {auto|enable|disable}"
Sets the reporting policy for VF link state to either
- mirror physical link state
- always up
- always down
get VF link state mode in efx_ef10_sriov_get_vf_config
Exercised by
"ip link show <PF intf>";
output will include a line like
vf 0 MAC 12:34:56:78:9a:bc, link-state auto
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max vlan tags that can be offloaded is 2, including any upstream VLAN
aggregator. Currently there is no way for the net driver to know whether
the upstream vswitch (if any) is using vlan tags, so there is no way to
know how many tags we can request.
Along with the implementation for the ndo_set_vf_vlan callback, this patch
also adds 2 VLAN tags for the driver created VEB switch if possible, that
way it is possible to offload as many tags as are allowed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do an entity reset when we detect an MC reboot.
This messes up SRIOV because it leaves VFs orphaned. The extra
reset is rather redundant anyway, since the MC reboot will have
basically reset everything.
This change replaces the entity reset after MC reboot with a
simpler datapath reset that reallocates resources but doesn't
perform the entity reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink calls ndo_get_vf_config when compiling information
about a network interface, so that the VFs associated with a PF
can be listed (eg: ip link show).
Implement a response to this entry point and return PF-set MAC
address for VF in ndo_get_vf_config
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
