On Bay Trail devices the MIPI power on/off sequences for DSI LCD panels
do not control the LCD panel- and backlight-enable GPIOs. So far, when
the VBT indicates we should use the SoC for backlight control, we have
been relying on these GPIOs being configured as output and driven high by
the Video BIOS (GOP) when it initializes the panel.
This does not work when the device is booted with a HDMI monitor connected
as then the GOP will initialize the HDMI instead of the panel, leaving the
panel black, even though the i915 driver tries to output an image to it.
Likewise on some device-models when the GOP does not initialize the DSI
panel it also leaves the mux of the PWM0 pin in generic GPIO mode instead
of muxing it to the PWM controller.
This commit makes the DSI code control the SoC GPIOs for panel- and
backlight-enable on BYT, when the VBT indicates the SoC should be used
for backlight control. It also ensures that the PWM0 pin is muxed to the
PWM controller in this case.
This fixes the LCD panel not lighting up on various devices when booted
with a HDMI monitor connected. This has been tested to fix this on the
following devices:
Peaq C1010
Point of View MOBII TAB-P800W
Point of View MOBII TAB-P1005W
Terra Pad 1061
Yours Y8W81
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-6-hdegoede@redhat.com
Move the Crystal Cove PMIC panel GPIO lookup-table from
drivers/mfd/intel_soc_pmic_core.c to the i915 driver.
The moved looked-up table is adding a GPIO lookup to the i915 PCI
device and the GPIO subsys allows only one lookup table per device,
The intel_soc_pmic_core.c code only adds lookup-table entries for the
PMIC panel GPIO (as it deals only with the PMIC), but we also need to be
able to access some GPIOs on the SoC itself, which requires entries for
these GPIOs in the lookup-table.
Since the lookup-table is attached to the i915 PCI device it really
should be part of the i915 driver, this will also allow us to extend
it with GPIOs from other sources when necessary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-5-hdegoede@redhat.com
When the LCD has not been turned on by the firmware/GOP, because e.g. the
device was booted with an external monitor connected over HDMI, we should
not turn on the panel-enable GPIO when we request it.
Turning on the panel-enable GPIO when we request it, means we turn it on
too early in the init-sequence, which causes some panels to not correctly
light up.
This commits adds a panel_is_on parameter to intel_dsi_vbt_gpio_init()
and makes intel_dsi_vbt_gpio_init() set the initial GPIO value accordingly.
This fixes the panel not lighting up on a Thundersoft TST168 tablet when
booted with an external monitor connected over HDMI.
Changes in v2:
- Call intel_dsi_get_hw_state() to check if the panel is on instead of
relying on the current_mode pointer
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-4-hdegoede@redhat.com
On some older devices (BYT, CHT) which may use v2 VBT MIPI-sequences,
we need to manually control the panel enable GPIO as v2 sequences do
not do this.
So far we have been carrying the code to do this on BYT/CHT devices
with a Crystal Cove PMIC in vlv_dsi.c, but as this really is a shortcoming
of the VBT MIPI-sequences, intel_dsi_vbt.c is a better place for this,
so move it there.
This is a preparation patch for adding panel-enable and backlight-enable
GPIO support for BYT devices where instead of the PMIC the SoC is used
for backlight control.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-3-hdegoede@redhat.com
drm-misc-next for v5.6:
UAPI Changes:
- Commandline parser: Add support for panel orientation, and per-mode options.
- Fix IOCTL naming for dma-buf heaps.
Cross-subsystem Changes:
- Rename DMA_HEAP_IOC_ALLOC to DMA_HEAP_IOCTL_ALLOC before it becomes abi.
- Change DMA-BUF system-heap's name to system.
- Fix leak in error handling in dma_heap_ioctl(), and make a symbol static.
- Fix udma-buf cpu access.
- Fix ti devicetree bindings.
Core Changes:
- Add CTA-861-G modes with VIC >= 193.
- Change error handling and remove bug_on in *drm_dev_init.
- Export drm_panel_of_backlight() correctly once more.
- Add support for lvds decoders.
- Convert drm/client and drm/(gem-,)fb-helper to drm-device based logging and update logging todo.
Driver Changes:
- Add support for dsi/px30 to rockchip.
- Add fb damage support to virtio.
- Use dma_resv locking wrappers in vc4, msm, etnaviv.
- Make functions in virtio static, and perform some simplifications.
- Add suspend support to sun4i.
- Add A64 mipi dsi support to sun4i.
- Add runtime pm suspend to komeda.
- Associated driver fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efc11139-1653-86bc-1b0f-0aefde219850@linux.intel.com
When configuring the frame memory window, the last column and row
numbers are written to the column resp. page address registers. These
numbers are thus one less than the actual window width resp. height.
While this is handled correctly in mipi_dbi_fb_dirty() since commit
03ceb1c8df ("drm/tinydrm: Fix setting of the column/page end
addresses."), it is not in mipi_dbi_blank(). The latter still forgets
to subtract one when calculating the most significant bytes of the
column and row numbers, thus programming wrong values when the display
width or height is a multiple of 256.
Fixes: 02dd95fe31 ("drm/tinydrm: Add MIPI DBI support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230130604.31006-1-geert+renesas@glider.be
Declare the temp variable as __be16 to address the following sparse
warning:
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: warning: incorrect type in initializer (different base types)
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: expected unsigned short [unsigned] [usertype] temp
drivers/gpu/drm/panel/panel-lg-lg4573.c:45:20: got restricted __be16 [usertype] <noident>
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230195609.12386-1-wambui.karugax@gmail.com
Currently only the drivers/pinctrl/devicetree.c code allows registering
pinctrl-mappings which may later be unregistered, all other mappings
are assumed to be permanent.
Non-dt platforms may also want to register pinctrl mappings from code which
is build as a module, which requires being able to unregister the mapping
when the module is unloaded to avoid dangling pointers.
To allow unregistering the mappings the devicetree code uses 2 internal
functions: pinctrl_register_map and pinctrl_unregister_map.
pinctrl_register_map allows the devicetree code to tell the core to
not memdup the mappings as it retains ownership of them and
pinctrl_unregister_map does the unregistering, note this only works
when the mappings where not memdupped.
The only code relying on the memdup/shallow-copy done by
pinctrl_register_mappings is arch/arm/mach-u300/core.c this commit
replaces the __initdata with const, so that the shallow-copy is no
longer necessary.
After that we can get rid of the internal pinctrl_unregister_map function
and just use pinctrl_register_mappings directly everywhere.
This commit also renames pinctrl_unregister_map to
pinctrl_unregister_mappings so that its naming matches its
pinctrl_register_mappings counter-part and exports it.
Together these 2 changes will allow non-dt platform code to
register pinctrl-mappings from modules without breaking things on
module unload (as they can now unregister the mapping on unload).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191216205122.1850923-2-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of tiled displays, all the tiles are linke dto each other
for transcoder port sync. So in intel_atomic_check() we need to make
sure that we add all the tiles to the modeset and if one of the
tiles needs a full modeset then mark all other tiles for a full modeset.
We also need to force modeset for all synced crtcs after fastset check.
v6:
* Add comments about why we do not call
drm_atomic_helper_check_modeset (Matt)
* Add FIXME for a corner case where tile info might vanish (Matt)
v5:
* Rebase
v4:
* Fix logic for modeset_synced_crtcs (Ville)
v3:
* Add tile checks only for Gen >11
v2:
* Change crtc_state scope, remove tile_grp_id (Ville)
* Use intel_connector_needs_modeset() (Ville)
* Add modeset_synced_crtcs (Ville)
* Make sure synced crtcs are forced full modeset
after fastset check (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-1-manasi.d.navare@intel.com
In case of tiled displays, if we hotplug just one connector,
fbcon currently just selects the preferred mode and if it is
tiled mode then that becomes a problem if rest of the tiles are
not present.
So in the fbdev driver on hotplug when we probe the client modeset,
if we dont find all the connectors for all tiles, then on a connector
with one tile, just fallback to the first available non tiled mode
to display over a single connector.
On the hotplug of the consecutive tiled connectors, if the tiled mode
no longer exists because of fbcon size limitation, then return
no modes for consecutive tiles but retain the non tiled mode
on the 0th tile.
Use the same logic in case of connected boot case as well.
This has been tested with Dell UP328K tiled monitor.
v3:
* Check Num tiled conns that are connected (Manasi)
v2:
* Set the modes on consecutive hotplugged tiles to no mode
if tiled mode is pruned (Dave)
v1:
* Just handle the 1st connector hotplug case
* v1 Reviewed-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Dave Airlie <airlied@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Dave Airlie <airlied@redhat.com> (v2)
Link: https://patchwork.freedesktop.org/patch/msgid/20191211212433.18185-2-manasi.d.navare@intel.com
