Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although devlink health report does a nice job on reporting TX
timeout and other NIC errors, unfortunately it requires drivers
to support it but currently only mlx5 has implemented it.
Before other drivers could catch up, it is useful to have a
generic tracepoint to monitor this kind of TX timeout. We have
been suffering TX timeout with different drivers, we plan to
start to monitor it with rasdaemon which just needs a new tracepoint.
Sample output:
ksoftirqd/1-16 [001] ..s2 144.043173: net_dev_xmit_timeout: dev=ens3 driver=e1000 queue=0
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2019-04-30
mlx5 misc updates:
1) Bodong Wang and Parav Pandit (6):
- Remove unused mlx5_query_nic_vport_vlans
- vport macros refactoring
- Fix vport access in E-Switch
- Use atomic rep state to serialize state change
2) Eli Britstein (2):
- prio tag mode support, added ACLs and replace TC vlan pop with
vlan 0 rewrite when prio tag mode is enabled.
3) Erez Alfasi (2):
- ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitions
- mlx5e: ethtool, Add support for EEPROM high pages query
4) Masahiro Yamada (1):
- remove meaningless CFLAGS_tracepoint.o
5) Maxim Mikityanskiy (1):
- Put the common XDP code into a function
6) Tariq Toukan (2):
- Turn on HW tunnel offload in all TIRs
7) Vlad Buslov (1):
- Return error when trying to insert existing flower filter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two possible utilizations so far:
- Switch devices that don't support a native insertion/extraction header
on the CPU port may still enjoy the benefits of port isolation with a
custom VLAN tag.
For this, they need to have a customizable TPID in hardware and a new
Ethertype to distinguish between real 802.1Q traffic and the private
tags used for port separation.
- Switches that don't support the deactivation of VLAN awareness, but
still want to have a mode in which they accept all traffic, including
frames that are tagged with a VLAN not configured on their ports, may
use this as a fake to trick the hardware into thinking that the TPID
for VLAN is something other than 0x8100.
What follows after the ETH_P_DSA_8021Q EtherType is a regular VLAN
header (TCI), however there is no other EtherType that can be used for
this purpose and doesn't already have a well-defined meaning.
ETH_P_8021AD, ETH_P_QINQ1, ETH_P_QINQ2 and ETH_P_QINQ3 expect that
another follow-up VLAN tag is present, which is not the case here.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an unified API for accessing register bit fields
regardless of memory layout. The basic unit of data for these API
functions is the u64. The process of transforming an u64 from native CPU
encoding into the peripheral's encoding is called 'pack', and
transforming it from peripheral to native CPU encoding is 'unpack'.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.
2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.
3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.
4) Inifnite loop in bpftool map create, from Alban Crequy.
5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
Chaignon.
6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
Dumazet.
7) Buffer overrun in marvell phy driver, from Andrew Lunn.
8) Several crash and statistics handling fixes to bnxt_en driver, from
Michael Chan and Vasundhara Volam.
9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
NULL deref, etc).
10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.
11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
Bruijn.
12) Use after free in l2tp, from Eric Dumazet.
13) IPV6 route destroy races, also from Eric Dumazet.
14) SCTP state machine can erroneously run recursively, fix from Xin
Long.
15) Adjust AF_PACKET msg_name length checks, add padding bytes if
necessary. From Willem de Bruijn.
16) Preserve skb_iif, so that forwarded packets have consistent values
even if fragmentation is involved. From Shmulik Ladkani.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
udp: fix GRO packet of death
ipv6: A few fixes on dereferencing rt->from
rds: ib: force endiannes annotation
selftests: fib_rule_tests: print the result and return 1 if any tests failed
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
net/tls: avoid NULL pointer deref on nskb->sk in fallback
selftests: fib_rule_tests: Fix icmp proto with ipv6
packet: validate msg_namelen in send directly
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
sctp: avoid running the sctp state machine recursively
stmmac: pci: Fix typo in IOT2000 comment
Documentation: fix netdev-FAQ.rst markup warning
ipv6: fix races in ip6_dst_destroy()
l2ip: fix possible use-after-free
appletalk: Set error code if register_snap_client failed
net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
rxrpc: Fix net namespace cleanup
ipv6/flowlabel: wait rcu grace period before put_pid()
vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
tcp: add sanity tests in tcp_add_backlog()
...
Pull io_uring fixes from Jens Axboe:
"This is mostly io_uring fixes/tweaks. Most of these were actually done
in time for the last -rc, but I wanted to ensure that everything
tested out great before including them. The code delta looks larger
than it really is, as it's mostly just comment additions/changes.
Outside of the comment additions/changes, this is mostly removal of
unnecessary barriers. In all, this pull request contains:
- Tweak to how we handle errors at submission time. We now post a
completion event if the error occurs on behalf of an sqe, instead
of returning it through the system call. If the error happens
outside of a specific sqe, we return the error through the system
call. This makes it nicer to use and makes the "normal" use case
behave the same as the offload cases. (me)
- Fix for a missing req reference drop from async context (me)
- If an sqe is submitted with RWF_NOWAIT, don't punt it to async
context. Return -EAGAIN directly, instead of using it as a hint to
do async punt. (Stefan)
- Fix notes on barriers (Stefan)
- Remove unnecessary barriers (Stefan)
- Fix potential double free of memory in setup error (Mark)
- Further improve sq poll CPU validation (Mark)
- Fix page allocation warning and leak on buffer registration error
(Mark)
- Fix iov_iter_type() for new no-ref flag (Ming)
- Fix a case where dio doesn't honor bio no-page-ref (Ming)"
* tag 'for-linus-20190502' of git://git.kernel.dk/linux-block:
io_uring: avoid page allocation warnings
iov_iter: fix iov_iter_type
block: fix handling for BIO_NO_PAGE_REF
io_uring: drop req submit reference always in async punt
io_uring: free allocated io_memory once
io_uring: fix SQPOLL cpu validation
io_uring: have submission side sqe errors post a cqe
io_uring: remove unnecessary barrier after unsetting IORING_SQ_NEED_WAKEUP
io_uring: remove unnecessary barrier after incrementing dropped counter
io_uring: remove unnecessary barrier before reading SQ tail
io_uring: remove unnecessary barrier after updating SQ head
io_uring: remove unnecessary barrier before reading cq head
io_uring: remove unnecessary barrier before wq_has_sleeper
io_uring: fix notes on barriers
io_uring: fix handling SQEs requesting NOWAIT
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes: f121e0ea95 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added max EEPROM length defines for ethtool usage:
#define ETH_MODULE_SFF_8636_MAX_LEN 640
#define ETH_MODULE_SFF_8436_MAX_LEN 640
These definitions are used to determine the EEPROM
data length when reading high eeprom pages.
For example, SFF-8636 EEPROM data from page 03h
needs to be stored at data[512] - data[639].
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit broke the offsets of hca cap struct, fix it.
While at it, cleanup a white space introduced by the same commit.
Fixes: b169e64a24 ("net/mlx5: Geneve, Add flow table capabilities for Geneve decap with TLV options")
Reported-by: Qian Cai <cai@lca.pw>
Cc: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1Q-2018 defines the concept of a cycle-time-extension, so the
last entry of a schedule before the start of a new schedule can be
extended, so "too-short" entries can be avoided.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1Q-2018 defines that a the cycle-time of a schedule may be
overridden, so the schedule is truncated to a determined "width".
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.
Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.
The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):
$ tc qdisc change taprio dev IFACE parent root \
base-time X \
sched-entry <CMD> <GATES> <INTERVAL> \
...
Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.
Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.
So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.
For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.
Example:
$ tc qdisc change dev IFACE parent root handle 100 taprio \
base-time $BASE_TIME \
sched-entry S 00 500000 \
sched-entry S 0f 500000 \
clockid CLOCK_TAI
The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.
With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 875f1d0769 ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
introduces one extra flag of ITER_BVEC_FLAG_NO_REF, and this flag
is stored into iter->type.
However, iov_iter_type() doesn't consider the new added flag, fix
it by masking this flag in iov_iter_type().
Fixes: 875f1d0769 ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ying triggered a call trace when doing an asconf testing:
BUG: scheduling while atomic: swapper/12/0/0x10000100
Call Trace:
<IRQ> [<ffffffffa4375904>] dump_stack+0x19/0x1b
[<ffffffffa436fcaf>] __schedule_bug+0x64/0x72
[<ffffffffa437b93a>] __schedule+0x9ba/0xa00
[<ffffffffa3cd5326>] __cond_resched+0x26/0x30
[<ffffffffa437bc4a>] _cond_resched+0x3a/0x50
[<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
[<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
[<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
[<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
[<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
[<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
[<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
[<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
[<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]
As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.
Vlad tried to fix this recursive call in Commit c078669340 ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.
To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since different types of hardware may or may not support this setting
per-port, DSA keeps it either in dsa_switch or in dsa_port.
While drivers may know the characteristics of their hardware and
retrieve it from the correct place without the need of helpers, it is
cumbersone to find out an unambigous answer from generic DSA code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull USB fixes from Greg KH:
"Here are some small USB fixes for a bunch of warnings/errors that the
syzbot has been finding with it's new-found ability to stress-test the
USB layer.
All of these are tiny, but fix real issues, and are marked for stable
as well. All of these have had lots of testing in linux-next as well"
* tag 'usb-5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: w1 ds2490: Fix bug caused by improper use of altsetting array
USB: yurex: Fix protection fault after device removal
usb: usbip: fix isoc packet num validation in get_pipe
USB: core: Fix bug caused by duplicate interface PM usage counter
USB: dummy-hcd: Fix failure to give back unlinked URBs
USB: core: Fix unterminated string returned by usb_string()
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-04-30
1) A lot of work to remove indirections from the xfrm code.
From Florian Westphal.
2) Support ESP offload in combination with gso partial.
From Boris Pismenny.
3) Remove some duplicated code from vti4.
From Jeremy Sowden.
Please note that there is merge conflict
between commit:
8742dc86d0 ("xfrm4: Fix uninitialized memory read in _decode_session4")
from the ipsec tree and commit:
c53ac41e37 ("xfrm: remove decode_session indirection from afinfo_policy")
from the ipsec-next tree. The merge conflict will appear
when those trees get merged during the merge window.
The conflict can be solved as it is done in linux-next:
https://lkml.org/lkml/2019/4/25/1207
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-04-30
1) Fix an out-of-bound array accesses in __xfrm_policy_unlink.
From YueHaibing.
2) Reset the secpath on failure in the ESP GRO handlers
to avoid dereferencing an invalid pointer on error.
From Myungho Jung.
3) Add and revert a patch that tried to add rcu annotations
to netns_xfrm. From Su Yanjun.
4) Wait for rcu callbacks before freeing xfrm6_tunnel_spi_kmem.
From Su Yanjun.
5) Fix forgotten vti4 ipip tunnel deregistration.
From Jeremy Sowden:
6) Remove some duplicated log messages in vti4.
From Jeremy Sowden.
7) Don't use IPSEC_PROTO_ANY when flushing states because
this will flush only IPsec portocol speciffic states.
IPPROTO_ROUTING states may remain in the lists when
doing net exit. Fix this by replacing IPSEC_PROTO_ANY
with zero. From Cong Wang.
8) Add length check for UDP encapsulation to fix "Oversized IP packet"
warnings on receive side. From Sabrina Dubroca.
9) Fix xfrm interface lookup when the interface is associated to
a vrf layer 3 master device. From Martin Willi.
10) Reload header pointers after pskb_may_pull() in _decode_session4(),
otherwise we may read from uninitialized memory.
11) Update the documentation about xfrm[46]_gc_thresh, it
is not used anymore after the flowcache removal.
From Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce support for Geneve flow specification and allow
the creation of rules that are matching on basic Geneve
protocol fields: VNI, OAM bit, protocol type, options length.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When in switchdev mode, we would like to treat loopback RoCE
traffic (on eswitch manager) as RDMA and not as regular
Ethernet traffic
In order to enable it we add flow steering rule that forward RoCE
loopback traffic to the HW RoCE filter (by adding allow rule).
In addition we add RoCE address in GID index 0, which will be
set in the RoCE loopback packet.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow table supports three types of miss action:
1. Default miss action - go to default miss table according to table.
2. Go to specific table.
3. Switch domain - go to the root table of an alternative steering
table domain.
New table miss action was added - switch_domain.
The next domain for RDMA_RX namespace is the NIC RX domain.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5 core stores copy of the PCI device name in a
mlx5_priv structure and uses pr_warn, pr_err helpers.
Get rid of the copy of this name; instead store the parent device
pointer that contains name as well as dma specific parameters.
This also allows to use kernel's well defined dev_warn, dev_err, dev_dbg
device specific print routines.
This is also a preparation patch to access non PCI parent device in
future.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets will be
tagged with VLAN ID 0x000 (priority tag) and pop/push actions will be
replaced by VLAN re-write actions (which are supported by the HW).
Introduce prio tag mode as a pre-step to controlling the workaround
behavior.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
