If more than 255 colocated APs exist for the set of all
APs found during 2.4/5 GHz scanning, then the 6 GHz scan
construction will loop forever since the loop variable
has type u8, which can never reach the number found when
that's bigger than 255, and is stored in a u32 variable.
Also move it into the loops to have a smaller scope.
Using a u32 there is fine, we limit the number of APs in
the scan list and each has a limit on the number of RNR
entries due to the frame size. With a limit of 1000 scan
results, a frame size upper bound of 4096 (really it's
more like ~2300) and a TBTT entry size of at least 11,
we get an upper bound for the number of ~372k, well in
the bounds of a u32.
Cc: stable@vger.kernel.org
Fixes: eae94cf82d ("iwlwifi: mvm: add support for 6GHz")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219375
Link: https://patch.msgid.link/20241023091744.f4baed5c08a1.I8b417148bbc8c5d11c101e1b8f5bf372e17bf2a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit dfdfe4be18 ("wifi: iwlwifi: remove retry loops in
start"), it turns out that there's an issue with the PNVM load
notification from firmware not getting processed, that this patch
has been somewhat successfully papering over. Since this is being
reported, revert the loop removal for now.
We will later at least clean this up to only attempt to retry if
there was a timeout, but currently we don't even bubble up the
failure reason to the correct layer, only returning NULL.
Fixes: dfdfe4be18 ("wifi: iwlwifi: remove retry loops in start")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241022092212.4aa82a558a00.Ibdeff9c8f0d608bc97fc42024392ae763b6937b7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we add the vif (and its default link) in fw restart we may
override the link that already exists. We take care of this but if
link 0 is a valid MLO link, then we will re-create a default link on
mvmvif->link[0] and we'll loose the real link we had there.
In non-MLO, we need to re-create the default link upon the interface
creation, this is fine. In MLO, we'll just wait for change_vif_links()
to re-build the links.
Fixes: bf976c814c ("wifi: iwlwifi: mvm: implement link change ops")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.385bfea1b2e9.I4a127312285ccb529cc95cc4edf6fbe1e0a136ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_send_ap_tx_power_constraint_cmd is a no-op if the link is not
active (we need to know the band etc.)
However, for the station case it will be called just before we set the
link to active (by calling iwl_mvm_link_changed with
the LINK_CONTEXT_MODIFY_ACTIVE bit set in the 'changed' flags and
active = true), so it will end up doing nothing.
Fix this by calling iwl_mvm_send_ap_tx_power_constraint_cmd before
iwl_mvm_link_changed.
Fixes: 6b82f4e119 ("wifi: iwlwifi: mvm: handle TPE advertised by AP")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.5c235fccd3f1.I2d40dea21e5547eba458565edcb4c354d094d82a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wireless fixes for v6.12-rc5
The first set of wireless fixes for v6.12. We have been busy and have
not been able to send this earlier, so there are more fixes than
usual. The fixes are all over, both in stack and in drivers, but
nothing special really standing out.
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
So, in order to avoid ending up with a flexible-array member in the
middle of multiple other structs, we use the `__struct_group()`
helper to create a new tagged `struct ieee80211_radiotap_header_fixed`.
This structure groups together all the members of the flexible
`struct ieee80211_radiotap_header` except the flexible array.
As a result, the array is effectively separated from the rest of the
members without modifying the memory layout of the flexible structure.
We then change the type of the middle struct members currently causing
trouble from `struct ieee80211_radiotap_header` to `struct
ieee80211_radiotap_header_fixed`.
We also want to ensure that in case new members need to be added to the
flexible structure, they are always included within the newly created
tagged struct. For this, we use `static_assert()`. This ensures that the
memory layout for both the flexible structure and the new tagged struct
is the same after any changes.
This approach avoids having to implement `struct ieee80211_radiotap_header_fixed`
as a completely separate structure, thus preventing having to maintain
two independent but basically identical structures, closing the door
to potential bugs in the future.
So, with these changes, fix the following warnings:
drivers/net/wireless/ath/wil6210/txrx.c:309:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2100.c:2521:50: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/ipw2200.h:1146:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/intel/ipw2x00/libipw.h:595:36: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:34:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/marvell/libertas/radiotap.h:5:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:10:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/microchip/wilc1000/mon.c:15:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:758:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/virtual/mac80211_hwsim.c:767:42: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/ZwBMtBZKcrzwU7l4@kspp
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iwlegacy uses command buffers with a payload size of 320
bytes (default) or 4092 bytes (huge). The struct il_device_cmd type
describes the default buffers and there is no separate type describing
the huge buffers.
The il_enqueue_hcmd() function works with both default and huge
buffers, and has a memcpy() to the buffer payload. The size of
this copy may exceed 320 bytes when using a huge buffer, which
now results in a run-time warning:
memcpy: detected field-spanning write (size 1014) of single field "&out_cmd->cmd.payload" at drivers/net/wireless/intel/iwlegacy/common.c:3170 (size 320)
To fix this:
- Define a new struct type for huge buffers, with a correctly sized
payload field
- When using a huge buffer in il_enqueue_hcmd(), cast the command
buffer pointer to that type when looking up the payload field
Reported-by: Martin-Éric Racine <martin-eric.racine@iki.fi>
References: https://bugs.debian.org/1062421
References: https://bugzilla.kernel.org/show_bug.cgi?id=219124
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 54d9469bc5 ("fortify: Add run-time WARN for cross-field memcpy()")
Tested-by: Martin-Éric Racine <martin-eric.racine@iki.fi>
Tested-by: Brandon Nielsen <nielsenb@jetfuse.net>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/ZuIhQRi/791vlUhE@decadent.org.uk
When a channel ctx is assigned to a link, we set the
LINK_CONTEXT_MODIFY_RATES_INFO to indicate that the rate fields are now
valid. But then we always take the rates of 2.4 GHz regardless of actual
used band.
This is because we are getting the band from bss_conf->chanctx_conf, but
this is assigned only after drv_assign_vif_chanctx returns, so we take
the bands of 2.4 GHz.
Fix it by taking the band from the iwl_mvm_link_info::phy_ctxt instead,
as this has already assigned in this point.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20240901071542.11c2d3609609.I8fa59e29b6bb38e5d06f3536d54dfb2c5d5bab11@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we de-activate a link because it started a CSA with mode=1, we want
to tell the firmware it can no longer transmit any frame for that link.
The firmware will do that on its own if the CSA indication (beacon /
action frame) was received on that same link, but with MLO, things got
more complex and the firmware can't track cross link CSA.
Tell the firmware if we de-activate a link because of CSA with mode=1 to
prevent it from transmitting, even if it is only an NDP PM=1 frame that
is part of the de-activation flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240901071542.4bef89d438d4.If7147a7a84054e67c05414c753d73f4e2e0e6e37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This shouldn't happen at all, since in station mode all MMPDUs
go through the TXQ for the STA, and not this function. There
may or may not be a race in mac80211 through which this might
happen for some frames while a station is being added, but in
that case we can also just drop the frame and pretend the STA
didn't exist yet.
Also, the code is simply wrong since it uses deflink, and it's
not easy to fix it since the mvmvif->ap_sta pointer cannot be
used without the mutex, and perhaps the right link might not
even be known.
Just drop the frame at that point instead of trying to fix it
up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45ad105dc7fe.I6d45c82e5758395d9afb8854057ded03c7dc81d7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the driver handles SMPS decisions by tracking AP
capabilities, BT coexistence changes, sending necessary SMPS
frames to the AP, and updating firmware with RX chain info
using the RLC_CONFIG_CMD.
Starting with version 3 of the RLC_CONFIG_CMD, the firmware
takes over this responsibility. It now tracks SMPS, sends
frames, and configures the RLC.
In this patch:
1. Stop sending RLC_CONFIG_CMD when firmware supports RLC
offload (version 3), as rlc.rx_chain_info is not needed by
firmware, and no other field in the cmd is used.
2. Prevent the driver from forwarding any SMPS requests to
mac80211, i.e., the driver should not transmit SMPS frames
to the AP as firmware handles that.
3. Set NL80211_FEATURE_DYNAMIC_SMPS and NL80211_FEATURE_STATIC_SMPS
conditionally based on RLC version.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45da23be1f65.I0d46db82dd990a82e8a66876fe2f5310bc9513be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the upper layer requests to cancel an ongoing scan, a race
is possible in which by the time the driver starts to handle the
upper layers scan cancel flow, the FW already completed handling
the scan request and the driver received the scan complete
notification but still did not handle the notification. In such a
case the FW will simply ignore the scan abort request coming from
the driver, no notification would arrive from the FW and the entire
abort flow would be considered a failure.
To better handle this, check the status code returned by the FW for
the scan abort command. In case the status indicates that
no scan was aborted, complete the scan abort flow with success, i.e.,
the scan was aborted, as the flow is expected to consume the scan
complete notification.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825085558.483989d3baef.I3340556a222388504c6330b333360bf77d10f9e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
