Needed by multi-family tables to distinguish IPv4 and IPv6 packets.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new table family and a new filter chain that you can
use to attach IPv4 and IPv6 rules. This should help to simplify
rule-set maintainance in dual-stack setups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support to register chains to multiple hooks for different address
families for mixed IPv4/IPv6 tables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Multi-family tables need the AF from the hook ops. Add a pointer to the
hook ops and replace usage of the hooknum member in struct nft_pktinfo.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we have one to three pinctrl-single instances for each SoC it is
a bit confusing to configure the padconf register offset from the
base of the padconf register base.
Let's add macros that allow using the physical address of the
padconf register directly, or in most cases, just the last 16-bits
of the address as they are shown in the documentation.
Note that most documentation shows two padconf registers for each
32-bit address, so adding 2 to the documentation address is needed for
the second padconf register as we treat them as 16-bit registers
for omap3+.
For example, omap36xx documentation shows sdmmc2_clk at 0x48002158,
so we can just use the last 16-bits of that value:
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
And we don't need to separately calculate the offset from the 0x2030
base:
pinctrl-single,pins = <
0x128 (PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
Naturally both ways of defining the registers can be used, and I'm
not saying we should replace all the existing defines. But it may
be handy to use these macros for new entries and when doing other
related .dts file clean-up.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 range]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows to follow a recommandation of RFC4942.
- Add "anycast_src_echo_reply" sysctl to control the use of anycast addresses
as source addresses for ICMPv6 echo reply. This sysctl is false by default
to preserve existing behavior.
- Add inline check ipv6_anycast_destination().
- Use them in icmpv6_echo_reply().
Reference:
RFC4942 - IPv6 Transition/Coexistence Security Considerations
(http://tools.ietf.org/html/rfc4942#section-2.1.6)
2.1.6. Anycast Traffic Identification and Security
[...]
To avoid exposing knowledge about the internal structure of the
network, it is recommended that anycast servers now take advantage of
the ability to return responses with the anycast address as the
source address if possible.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some BE DAIs can be "dummy" (when the DSP is controlling the DAI) and as such
wont have set a minimum number of playback or capture channels required for BE
DAI registration (to establish supported stream directions).
Force machine drivers to explicitly set whether they support playback and capture
stream directions for every BE DAIs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
this gives ability to convey the valid values of supported rates in
sample_rates array
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently Intel interrupt remapping drivers uses the "present" flag bit
in remapping entry to track whether an entry is allocated or not.
It works as follow:
1) allocate a remapping entry and set its "present" flag bit to 1
2) compose other fields for the entry
3) update the remapping entry with the composed value
The remapping hardware may access the entry between step 1 and step 3,
which then observers an entry with the "present" flag set but random
values in all other fields.
This patch introduces a dedicated bitmap to track remapping entry
allocation status instead of sharing the "present" flag with hardware,
thus eliminate the race window. It also simplifies the implementation.
Tested-and-reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
domain_has_cap is a misnomer bc the func name should be
the same for CONFIG_IOMMU_API and !CONFIG_IOMMU_API.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Some embedded systems use hibernation for fast boot. and in it,
some software components need to handle specific things before
hibernation and after restore. So it needs to capture the apm
status about these pm events.
Currently apm just supports suspend to ram, but not suspend to disk,
so here add logic about hibernation apm events.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If start_streaming returns -ENOBUFS, then it will be retried the next time
a buffer is queued. This means applications no longer need to know how many
buffers need to be queued before STREAMON can be called. This is particularly
useful for output stream I/O.
If a DMA engine needs at least X buffers before it can start streaming, then
for applications to get a buffer out as soon as possible they need to know
the minimum number of buffers to queue before STREAMON can be called. You can't
just try STREAMON after every buffer since on failure STREAMON will dequeue
all your buffers. (Is that a bug or a feature? Frankly, I'm not sure).
This patch simplifies applications substantially: they can just call STREAMON
at the beginning and then start queuing buffers and the DMA engine will
kick in automagically once enough buffers are available.
This also fixes using write() to stream video: the fileio implementation
calls streamon without having any queued buffers, which will fail today for
any driver that requires a minimum number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than taking the mmap semaphore at a relatively high-level function,
push it down to the place where it is really needed.
It was placed in vb2_queue_or_prepare_buf() to prevent racing with other
vb2 calls. The only way I can see that a race can happen is when two
threads queue the same buffer. The solution for that it to introduce
a PREPARING state.
Moving it down offers opportunities to simplify the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GRO/GSO layers can be enabled on a node, even if said
node is only forwarding packets.
This patch permits GSO (and upcoming GRO) support for GRE
encapsulated packets, even if the host has no GRE tunnel setup.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This API can be used by drivers to send their custom
configuration using SET_CONFIG NCI command to the device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers require special configuration while initializing.
This patch adds setup handler for this custom configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking fixes from David Miller:
"I'm hoping this is the very last batch of networking fixes for 3.13,
here goes nothing:
1) Fix crashes in VLAN's header_ops passthru.
2) Bridge multicast code needs to use BH spinlocks to prevent
deadlocks with timers. From Curt Brune.
3) ipv6 tunnels lack proper synchornization when updating percpu
statistics. From Li RongQing.
4) Fixes to bnx2x driver from Yaniv Rosner, Dmitry Kravkov and Michal
Kalderon.
5) Avoid undefined operator evaluation order in llc code, from Daniel
Borkmann.
6) Error paths in various GSO offload paths do not unwind properly,
in particular they must undo any modifications they have made to
the SKB. From Wei-Chun Chao.
7) Fix RX refill races during restore in virtio-net, from Jason Wang.
8) Fix SKB use after free in LLC code, from Daniel Borkmann.
9) Missing unlock and OOPS in netpoll code when VLAN tag handling
fails.
10) Fix vxlan device attachment wrt ipv6, from Fan Du.
11) Don't allow creating infiniband links to non-infiniband devices,
from Hangbin Liu.
12) Revert FEC phy reset active low change, it breaks things. From
Fabio Estevam.
13) Fix header pointer handling in 6lowpan header building code, from
Daniel Borkmann.
14) Fix RSS handling in be2net driver, from Vasundhara Volam.
15) Fix modem port indexing in HSO driver, from Dan Williams"
* http://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
bridge: use spin_lock_bh() in br_multicast_set_hash_max
ipv6: don't install anycast address for /128 addresses on routers
hso: fix handling of modem port SERIAL_STATE notifications
isdn: Drop big endian cpp checks from telespci and hfc_pci drivers
be2net: fix max_evt_qs calculation for BE3 in SR-IOV config
be2net: increase the timeout value for loopback-test FW cmd
be2net: disable RSS when number of RXQs is reduced to 1 via set-channels
xen-netback: Include header for vmalloc
net: 6lowpan: fix lowpan_header_create non-compression memcpy call
fec: Revert "fec: Do not assume that PHY reset is active low"
bnx2x: fix VLAN configuration for VFs.
bnx2x: fix AFEX memory overflow
bnx2x: Clean before update RSS arrives
bnx2x: Correct number of MSI-X vectors for VFs
bnx2x: limit number of interrupt vectors for 57711
qlcnic: Fix bug in Tx completion path
infiniband: make sure the src net is infiniband when create new link
{vxlan, inet6} Mark vxlan_dev flags with VXLAN_F_IPV6 properly
cxgb4: allow large buffer size to have page size
netpoll: Fix missing TXQ unlock and and OOPS.
...
Drop user features if an outdated user space instance that does not
understand the concept of user_features attempted to create a new
datapath.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Allocates a new sk_buff large enough to cover the specified payload
plus required Netlink headers. Will check receiving socket for
memory mapped i/o capability and use it if enabled. Will fall back
to non-mapped skb if message size exceeds the frame size of the ring.
Signed-of-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
