Merge tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Not a huge amount going on this release, mainly new drivers (there's a
  couple more waiting that didn't quite make the cut for this release
  too):

   - An interface for querying if the current transfer is the last in a
     message, allowing controllers that need special handling for the
     final transfer to use the core message parsing.
   - Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
     Intel Quark X1000 and Samsung Exynos 7 controllers"

* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
  spi/s3c64xx: Remove redundant runtime PM management
  spi: fsl-spi: remove unused variable assignment
  spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
  spi: core: Do not mangle error code from kthread_run()
  spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
  spi: fsl-(e)spi: migrate to generic master queueing
  spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
  spi: cadence: Fix 3-to-8 mux mode
  spi: cadence: Init HW after reading devicetree attributes
  spi: meson: Select REGMAP_MMIO
  spi: s3c64xx: add support for exynos7 SPI controller
  spi: spi-pxa2xx: SPI support for Intel Quark X1000
  spi: meson: meson_spifc_setup_speed() can be static
  spi: spi-pxa2xx: Add helpers for regiseters' accessing
  spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
  spi: atmel: introduce probe deferring
  spi: atmel: remove compat for non DT board when requesting dma chan
  spi: meson: Add support for Amlogic Meson SPIFC
  spi: meson: Add device tree bindings documentation for SPIFC
  spi: core: Add spi_transfer_is_last() helper
  ...

Documentation/devicetree/bindings/spi/spi-gpio.txt

@@ -8,8 +8,10 @@ Required properties:
  - gpio-sck: GPIO spec for the SCK line to use
  - gpio-miso: GPIO spec for the MISO line to use
  - gpio-mosi: GPIO spec for the MOSI line to use
- - cs-gpios: GPIOs to use for chipselect lines
- - num-chipselects: number of chipselect lines
+ - cs-gpios: GPIOs to use for chipselect lines.
+             Not needed if num-chipselects = <0>.
+ - num-chipselects: Number of chipselect lines. Should be <0> if a single device
+                    with no chip select is connected.
 
 Example:
 

Documentation/devicetree/bindings/spi/spi-img-spfi.txt

@@ -0,0 +1,37 @@
+IMG Synchronous Peripheral Flash Interface (SPFI) controller
+
+Required properties:
+- compatible: Must be "img,spfi".
+- reg: Must contain the base address and length of the SPFI registers.
+- interrupts: Must contain the SPFI interrupt.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clock/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - spfi: SPI operating clock
+  - sys: SPI system interface clock
+- dmas: Must contain an entry for each entry in dma-names.
+  See ../dma/dma.txt for details.
+- dma-names: Must include the following entries:
+  - rx
+  - tx
+- #address-cells: Must be 1.
+- #size-cells: Must be 0.
+
+Optional properties:
+- img,supports-quad-mode: Should be set if the interface supports quad mode
+  SPI transfers.
+
+Example:
+
+spi@18100f00 {
+	compatible = "img,spfi";
+	reg = <0x18100f00 0x100>;
+	interrupts = <GIC_SHARED 22 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&spi_clk>, <&system_clk>;
+	clock-names = "spfi", "sys";
+	dmas = <&mdc 9 0xffffffff 0>, <&mdc 10 0xffffffff 0>;
+	dma-names = "rx", "tx";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+};

Documentation/devicetree/bindings/spi/spi-meson.txt

@@ -0,0 +1,22 @@
+Amlogic Meson SPI controllers
+
+* SPIFC (SPI Flash Controller)
+
+The Meson SPIFC is a controller optimized for communication with SPI
+NOR memories, without DMA support and a 64-byte unified transmit /
+receive buffer.
+
+Required properties:
+ - compatible: should be "amlogic,meson6-spifc"
+ - reg: physical base address and length of the controller registers
+ - clocks: phandle of the input clock for the baud rate generator
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+	spi@c1108c80 {
+		compatible = "amlogic,meson6-spifc";
+		reg = <0xc1108c80 0x80>;
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};

Documentation/devicetree/bindings/spi/spi-samsung.txt

@@ -9,7 +9,7 @@ Required SoC Specific Properties:
     - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
     - samsung,s3c6410-spi: for s3c6410 platforms
     - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
-    - samsung,exynos4210-spi: for exynos4 and exynos5 platforms
+    - samsung,exynos7-spi: for exynos7 platforms
 
 - reg: physical base address of the controller and length of memory mapped
   region.